@article { author = {Ghomeshi, M. and Jahanshahi, M. and Zayeri, M.R.}, title = {Simulation of Sediment Deposition in Jiroft Reservoir Using GSTARS3 Model}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {1-10}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     Dams are one of the most common structures to make a reservoir for water accumulation. Sediment deposition in reservoirs not only reduces the storage capacity of a reservoir but also decreases its useful life. Also, in many cases sedimentation creates problems for bottom outlets. In this study simulation of sediment deposition in Jiroft Reservoir is investigated with the aids of GSTARS3 model. At first the measured data of Jiroft Reservoir are used to calibrate the mathematical model. The Manning coefficient and the sediment transport equations are used for this proposed. After calibration, existing data are used for verification of the model. Finally, the time variation of reservoir volume is calculated. The results showed that the mean annual volume reduction of the reservoir is approximately equal to 1.27 percent of initial volume. Also, the trap efficiency of the reservoir is computed and it was equal to 87 percent.}, keywords = {reservoirs sedimentation,Jiroft dam,GSTARS3}, title_fa = {پیش بینی روند رسوب گذاری در مخزن سد جیرف با استفاده از مدل GSTAR3}, abstract_fa = {     احداث سد از متداولترین روش ها جهت بهره برداری از سیستم منابع آب سطحی بوده که هزینه های بسیار هنگفتی در قالب طرح های عظیم ملی صرف ساخت آن می­شود. رسوب گذاری در مخزن سد نه تنها سبب کاهش ظرفیت و عمر مخزن می شود، بلکه ضمن ایجاد اشکالات عدیده در باز و بسته کردن دریچه های عمقی و نیمه عمقی سد، موجب افزایش سطح مخزن و افزایش تبخیر و تلفات آب می  شود. در این تحقیق با استفاده از مدل GATARS3  وضعیت رسوبگذاری سد جیرفت مورد بررسی قرار گرفت. بعد از واسنجی مدل به کمک داده های آبنگاری مخزن سد جیرفت نحوه رسوبگذاری در مقطع طولی و عرضی ترسیم گردید. در هر مرحله از کالیبراسیون ضرایب به گونه ای تعیین می گردید که مقدار تابع خطای RMSE حداقل گردد. با توجه به پیش بینی مدل در سال 1443 حدود 80 درصد از حجم مخزن از رسوب پر می گردد به عبارتی دیگر سالیانه به طور متوسط حدود 23/1 درصد از حجم اولیه مخزن کاسته می شود و همچنین راندمان تله اندازی 87 درصد محاسبه گردید.  }, keywords_fa = {reservoirs sedimentation,Jiroft dam,GSTARS3}, url = {https://jise.scu.ac.ir/article_10515.html}, eprint = {https://jise.scu.ac.ir/article_10515_878a78ca08f06b472f10c8062af535f4.pdf} } @article { author = {Molavi, H. and Mohammadi, M. and Liaghat, A.}, title = {Effect of Saline Water Management on Yield and Yield Components of Corn and Soil Salinity Profile}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {11-18}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {Increasing demand of water resources in the world, especially in arid and semi-arid regions, has forced farmers to use low quality water, such as drainage water and saline groundwater. In order to evaluate the effects of saline water management on corn yield and salt distribution in soil profile, five management methods were conducted in a lysimetry study in Karaj. Therefore, the experiment was performed as a randomized complete block design with three replications by Furrow irrigation including five treatments: irrigation with non-saline water (M1=0.7 dS/m), irrigation with saline water (M2=5 dS/m), irrigation with mixed water (M3=2.85 dS/m), alternative irrigation with non-saline and saline water (M4) and alternative furrow irrigation simultaneously with saline and non-saline water (M5). In the latter one a furrow was irrigated with saline water and side furrow with non-saline water constantly. The results showed that highest yield and measured characteristics were corresponded to irrigation method with non-saline water (6988.12 kg/ha) and the least one with saline water (4090.76 kg/ ha). Yield decreased 20.59, 16.34 and 8.77 percent in M3, M4 and M5 treatments respectively as compared to the control treatment (M1). The average soil salinity in top 30 cm layer was 3.66, 2.66, 2.36 and 2.15 dS/m in M2, M3, M4 and M5 treatments, respectively. Therefore, it can be concluded that the best management practices among proposed treatments is alternative Furrow irrigation simultaneously with saline and non-saline water.}, keywords = {distribution of salinity,Corn,Yield,saline water management}, title_fa = {اثر مدیریت آب شور طی دوره رشد بر عملکرد و اجزای عملکرد ذرت دانه ای و پروفیل شوری خاک}, abstract_fa = {افزایش تقاضا برای منابع آب در جهان به خصوص در مناطق خشک و نیمه خشک، سبب شده است کشاورزان از آب های با کیفیت پایین مانند آب زهکشی و آب  زیرزمینی شور استفاده کنند. به منظور ارزیابی اثر مدیریت آب شور بر عملکرد ذرت دانه ای (رقم DC370) و توزیع شوری در نیمرخ خاک پنج روش مدیریتی در منطقه کرج و در شرایط لایسیمتری اجرا شد. بدین منظور، آزمایشی در قالب طرح بلوک های کاملا تصادفی با سه تکرار به صورت آبیاری جوی و پشته ای اجرا گردید. تیمارها عبارت بودند از: آبیاری با آب غیر شور (dS/m 7/0=M1)، آبیاری با آب شور (dS/m 5=M2)، استفاده از مخلوط آب غیر شور و شور (dS/m 85/2=M3)، آبیاری تناوبی با آب غیر شور و آب شور (M4) و آبیاری یک در میان جویچه ها به طور هم زمان با آب شور و غیر شور (یک جویچه با آب شور و جویچه کناری با آب غیر شور بطور ثابت تا انتهای فصل، M5). نتایج نشان داد، بیشترین مقدار عملکرد و صفات اندازه گیری شده، مربوط به روش آبیاری با آب غیر شور (12/6988 کیلوگرم در هکتار) و کمترین آن مربوط به روش آبیاری با آب شور (76/4090 کیلوگرم در هکتار) بود. در تیمار های M3، M4 و M5 عملکرد به ترتیب 59/20، 34/16 و 77/8 درصد نسبت به تیمار شاهد (M1) کاهش یافت. مقدار متوسط شوری در اعماق کمتر از 30 سانتی متری در تیمارهای M2، M3، M4 و M5 به ترتیب 66/3، 66/2، 36/2 و 15/2 دسی زیمنس بر متر بود. بنابراین بهترین روش مدیریتی در میان تیمارهای اعمال شده، روش آبیاری یک در میان جویچه ها با آب شور و غیر شور به طور همزمان می باشد.}, keywords_fa = {distribution of salinity,Corn,Yield,saline water management}, url = {https://jise.scu.ac.ir/article_10516.html}, eprint = {https://jise.scu.ac.ir/article_10516_f94c1b9f1df1e8d46af6ce1f8fc3a80d.pdf} } @article { author = {Mardookhpour, Alireza}, title = {Application of mathematical model SEBRM for evaluating the effect of temporary fall on runoff (Case study:Sepidroud catchment)}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {19-25}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {    Generally, the influence of temporary rain fall on runoff response may be simulated by a hydrograph. In this research study, based on statistical model, for evaluating the temporary rain fall hydrograph on run off peak, by considering two specified rain fall and producing a runoff model, simulation has been done in a small basin. The mathematical model, namely SEBRM, derived from primary data of two rainfall events and produced runoff of SepidroudBasin, reconstructed and a hyetograph is simulated by two certain rainfalls and calibration of obtained data would be the basis of evaluating of future runoff. The results show the SEBRM model in low and moderate rainfalls intensity, submits very closely convergence between actual and predicted data for describing the role of rainfall volume in producing runoff in small basins. So, in this research study, the error in computations, for maximum 60 mm/h rainfalls intensity, was 13% for SepidroudBasin approximately. }, keywords = {Runoff,maximum discharge,Simulation,mathematical model of SEBRM,Sepidroud basin}, title_fa = {کاربرد مدل ریاضی سبرم1 برای ارزیابی تأثیر توزیع بارش موقت بر تولید سیلاب (مطالعه موردی: حوضه آبریز سفیدرود)}, abstract_fa = {     به طور کلی می توان از روی هیدروگراف، پاسخ یک حوضه آبریز را نسبت به واقعه سیلاب تعیین نمود. در تحقیق حاضر برای ارزیابی تأثیر هیدروگراف بارش موقت بر تولید سیلاب در حوضه های کوچک، با در نظر گرفتن دو بارش با مشخصات معین و ایجاد یک مدل رواناب برمبنای آمار و احتمالات، شبیه سازی انجام شده است. مدل ریاضی ارائه شده که سبرم نام دارد از داده های اولیه دو واقعه بارش و رواناب حاصل از آن در حوضه آبی سپید رود ساخته می­شود که در آن یک هایتوگراف از دو بارش مشخص شبیه سازی شده و کالیبراسیون اعداد حاصله از آن، مبنای ارزیابی سیلاب­های آتی قرار می­گیرد. نتایج حاصله نشان می­داد که مدل ریاضی سبرم در شدت بارش­های متوسط و کم، در حوضه های کوچک و متوسط انطباق بسیارنزدیکی با مقادیر واقعی بارش ارائه می نماید به گونه ای که در تحقیق حاضر برای حوضه آبریز سپیدرود با حداکثرشدت بارش حدود  60 میلی­متر در ساعت ، تنها 13 درصد خطا مشاهده شد . }, keywords_fa = {Runoff,maximum discharge,Simulation,mathematical model of SEBRM,Sepidroud basin}, url = {https://jise.scu.ac.ir/article_10775.html}, eprint = {https://jise.scu.ac.ir/article_10775_42cc85cece9f0da3a20edadcf6920b00.pdf} } @article { author = {Nasrollahi, Aliheidar and Behzad, Majid and Boromannasab, Saeid and Ramezanimoghadam, Javad}, title = {Evaluation of Hydraulic Performance of the Compensating and Non-Compensating Emitters in Various Pressures and Temperatures}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {27-35}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {Discharge of emitters changes by various factors such as pressure, manufacturing coefficient of variation, clogging and the temperature of water irrigation. In order to study the effects of temperature on discharge of emitters, 10 types of emitters have been tested in irrigation laboratory in Faculty of Water Sciences Engineering Ahwaz, ShahidCharmUniversity. In this research, the effect of 4 different temperatures i.e. 10, 20, 30, 40°C under 4 pressures i.e. 5, 10, 15, 20 m was reviewed. By calculation of manufacturing coefficient of variation and based on American Society of Agricultural Engineers Standard, qualitative classification of emitters was done. Finally, four type were excellent, two of them unusable and the others  were between both conditions. For experiments in temperature of 10° , the ice and in temperatures of 30° and 40°, a tank equipped with an electric heater and controlling unit for temperature was used respectively. With regard to obtained results by raising temperature of irrigation water, the discharge of non-compensating emitters was increased. In compensating emitters, the temperature didn't have significant effect on discharge of emitters in 3 cases, but in two types cause  discharge was decreased and in one, discharge was increased. In final, result showed that temperature doesn't have a significant effect on manufacturing coefficient of variation and water emission Uniformity.}, keywords = {Emitter,manufacturing coefficient of variation,Pressure,water temperature}, title_fa = {بررسی عملکرد هیدرولیکی قطره‌چکان‌های تنظیم‌کننده و غیرتنظیم‌کننده فشار در فشار و دماهای مختلف}, abstract_fa = {دبی قطره­چکان تحت تأثیر عوامل گوناگونی همچون فشار،  ضریب تغییرات ساخت، گرفتگی و دمای آب آبیاری تغییر می­کند. به منظور بررسی اثر دما بر دبی قطره­چکان­ها، 10 نوع قطره­چکان در آزمایشگاه آبیاری دانشکده مهندسی علوم آب دانشگاه شهید چمران اهواز مورد آزمایش قرار گرفت. در این تحقیق اثر چهار دمای مختلف آب شامل 10، 20، 30و 40 درجه سانتی­گراد در چهار فشار 5، 10، 15و 20 متر بررسی شد. با محاسبه ضریب تغییرات ساخت و  استفاده از استاندارد انجمن مهندسان کشاورزی آمریکا طبقه بندی کیفی قطره­چکان­ها صورت گرفت که در نتیجه آن چهار نمونه عالی، دو نمونه غیر قابل استفاده و بقیه در بین این دو حالت بودند.  برای انجام آزمایش­های در دمای 10 درجه از یخ و در دماهای 30و 40 درجه از مخزنی مجهز به المنت و دستگاه کنترل کننده درجه حرارت استفاده شد. با توجه به نتایج به دست آمده، با افزایش دمای آب آبیاری دبی قطره­چکان­های غیر تنظیم کننده فشار افزایش یافت. در تنظیم کننده ­های فشار افزایش دما در سه مورد اثر معنی­دار روی دبی قطره­چکان­ها نداشت، در دو نوع  باعث کاهش دبی و در یک مورد باعث افزایش دبی شد. در پایان مشخص شد دما اثر معنی­دار روی ضریب تغییرات ساخت و یکنواختی پخش آب  ندارد.}, keywords_fa = {Emitter,manufacturing coefficient of variation,Pressure,water temperature}, url = {https://jise.scu.ac.ir/article_10778.html}, eprint = {https://jise.scu.ac.ir/article_10778_98766c84f0f718e2d1a2503b5acd9d7e.pdf} } @article { author = {Bakhtiari, Morteza and Kashefipour, Seyed Mahmood and Asghari pari, Seyed Amin}, title = {Evaluation the effect of transverse structures on the flood plain using hydraulic model HEC-RAS in Geographic Information Systems (GIS)}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {37-46}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {Rivers have always a significant role in foundation, evolution and development of human civilizations and societies. Along  a river, different organizations construct many longitudinal and transverse hydraulic structures for different purposes that these type of structurs cause many changes in morphology and dynamic of such rivers. In this research  study, the effect of the transverse structures to the flow direction built on BarajinRiver in Qazvin province on flood zone and land uses has been investigated. For this purpose the river plan, longitudinal  river profile and cross sections were provided using topographic and land use maps. In the next step, flood hydraugraphs different and the peak discharges were provided using different methods such as SCS with different return periods. The geometric data of river and its hydraulic structures were then collected using surveying information. HEC-RAS and GIS Softwares, which are popular for river engineering, were applied in this research. Flood mapping zones were provided with and without structures for different return periods. The predicted results were then compared with the corresponding meansured values and these comparisons showed the accuracy of those softwares.}, keywords = {transverse structures,flood zoon,Geographic Information Systems (GIS)}, title_fa = {بررسی تأثیرسازه‌های عرضی بر روی پهنه سیلاب با استفاده از مدل هیدرولیکیHEC-RAS در محیط سامانه اطلاعات جغرافیایی GIS}, abstract_fa = {     رودخانه­ها همواره در پیدایش، تکامل و توسعه تمدن‌ها و جوامع بشری نقش قابل توجهی داشته­اند. در طول مسیر یک رودخانه ارگان­های مختلف به منظورهای متفاوت سازه­های طولی و عرضی احداث می­نمایند که این نوع سازه­ها موجبات تغییرات ریخت‏شناسی و دینامیکی رودخانه را فراهم می‏آورند. در این تحقیق، اثر سازه­های عرضی احداث شده روی رودخانه باراجین واقع در استان قزوین بر روی پهنه سیلاب و نیز کاربری­های حاشیه این رودخانه مورد بررسی قرار گرفته است. برای این منظور پس از تهیه نقشه­های توپوگرافی و نیز کاربری اراضی، پلان و پروفیل طولی و عرضی رودخانه مورد مطالعه استخراج گردید. در گام بعد هیدروگراف­های سیل با روش­های مختلف از جمله SCS در دوره بازگشت­های مختلف تعیین و دبی اوج سیلاب­ها برآورد گردید. در مرحله بعد با استفاده از نتایج عملیات نقشه­برداری اطلاعات هندسی رودخانه و سازه­های عرضی واقع بر آن جمع­آوری گردید. نرمافزار مورد استفادهدر این تحقیق ترکیب نرم­افزار HEC-RAS و سامانه اطلاعات جغرافیایی (GIS) بوده که از جمله نرم­افزارهای متداول در زمینه مهندسی رودخانه می­باشند. در این مرحله نقشه­های پهنه­بندی سیل در دوره بازگشت­های مختلف و برای حالت­های با اعمال سازه­ها و بدون اعمال سازه­ها تهیه گردید. سپس با نتایج به دست آمده مقایسه صورت پذیرفت. نتایج حاصل نشان دهنده دقت بالای ترکیب سامانه اطلاعات جغرافیایی و نرم­افزار هیدرولیکی HEC-RAS در استخراج پهنه سیلاب و مدل­سازی رودخانه می­باشد.}, keywords_fa = {transverse structures,flood zoon,Geographic Information Systems (GIS)}, url = {https://jise.scu.ac.ir/article_10779.html}, eprint = {https://jise.scu.ac.ir/article_10779_0a148c00cf90ac0e1117d4d6df7c5db3.pdf} } @article { author = {Ghadoo, Yosef and Shafai-Bejestan, Mahmood and Fathi-Mogadam, Manoochehr and Soozepoor, Aziz}, title = {Experimental Investigation of Effect of Bank Roughness on Flow Patterns in a 90 Degree Sharp Bend}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {47-57}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {The present study has been conducted in a 90 degrees sharp bend to investigate the effect of bank roughness on flow patterns. Tests conducted under two different flow conditions, with Froude numbers equal to 0.17 and 0.4 and two different roughness sizes of 0.5 and 5.0 mm. In each test three components of flow velocity at 576 point were measured. Plot of flow velocity vectors and stream lines were done by SURFER and TECPLOT softwares. The results show that the region of maximum flow at the beginning of bend occurs at the inner bank then gradually shifted toward the outer bank at the end of bend. Comparison of flow patterns in two different roughnesses shows that by increasing the roughness height, the strength of secondary flow decreases while the number of smaller rotational cells is increased. In general it may be said that in a sharp bend up to cross section of 70, the region of high shear stress is very closed to the inner bank and from that place to the downstream, it shifted to the outer bank. The increases of bank roughness causes that the maximum shear stress is decreases. The location of maximum and minimum shear stress at two roughness of 0.5 and 5.0 mm are at 20 and 90 respectively, their values have been calculated to be 1.47 and 0.54 N/m2 for 0.5 mm roughness and 2.2 and 0.46 N/m2 for 5.0 mm roughness, respectively.}, keywords = {Sharp bend,bank roughness,rotational cell,Shear Stress}, title_fa = {تبررسی آزمایشگاهی تاثیر زبری جداره کانال بر روی الگوی جریان در قوس 90 درجه تند}, abstract_fa = {تحقیق حاضر به منظور بررسی تاثیر زبری جدارهی کانال بر روی الگوی جریان در قوس 90 درجه تند با نسبت شعاع انحنا خط مرکزی به عرض 2 و مقطع عرضی مستطیلی انجام شد. آزمایش­ها در دو شرایط مختلف جریان با اعداد فرود 17/0 و 4/0 و دو اندازه زبری5/0 و 5 میلی­متر انجام گرفت. در هر آزمایش و در طول قوس مولفه‌های سه بعدی سرعت جریان در 576 نقطه اندازه گیری شد. ترسیم بردارهای سرعت و الگوی جریان با استفاده از نرم‌افزارهای  SURFERو TECPLOT انجام گرفت. نتایج نشان داد که ناحیه حداکثر سرعت در ابتدا سمت جداره داخلی بوده و سپس به تدریج به سمت جداره خارجی جابجا شده به طوری که در انتهای پیچ کاملا در نزدیکی جداره خارجی می­باشد. همچنین با مقایسه الگوی جریان در دو زبری نتایج نشان داد که با افزایش زبری قدرت جریان­های ثانویه کاهش و به تعداد سلول های چرخشی با قدرت کمتر افزوده می­شود. در حالت کلی می­توان گفت در قوس تند تا مقطع 70 درجه، ناحیه با تنش برشی زیاد نزدیک جداره داخلی بوده و از 70 درجه به پایین دست به طرف جداره بیرونی قوس کشیده می­شود. همچنین افزایش زبری جداره باعث افزایش تنش برشی حداکثر و کاهش تنش برشی حداقل شده است. محل تشکیل بیشترین و کمترین مقدارتنش برشی در دو زبری5/0و 5 میلی­متر به ترتیب 20 درجه و90 درجه قوس بود که در زبری 5/0 میلی­متر به ترتیب برابر47/1 و 54/0 نیوتن بر متر مربع و در زبری 5 میلی­متر به ترتیب برابر2/2 و 46/0 نیوتن بر متر مربع بوده است. }, keywords_fa = {Sharp bend,bank roughness,rotational cell,Shear Stress}, url = {https://jise.scu.ac.ir/article_10781.html}, eprint = {https://jise.scu.ac.ir/article_10781_6714be119c3c0315fa83d2e8a12c3e94.pdf} } @article { author = {Rahimi, Daryosh and Mirhashemi, Hamid and Abedi, Fatemeh}, title = {Analysis of Thermodynamic and Synoptic Pick Floods in Arid Regions (Zayanderood Basin)}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {59-68}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {Heavy rainfalls are one of the crisis couses.The crisis of heavy rainfall in arid area are strong .in this study Zayandehrood basin as a arid area have storng floods in recent years.Statistical analysis in this period(1972-2010) indicate March flood that is ocured with 646 m3/s discharge and standard indicis SFI=10.47, is the biggest flood .In this study thermodinamic and synoptic conditions are anylyzed by Raklif and Bradbari indices.The SKW-T chart and upper air data in 500 mb are used. Bradbury and Rackliff Index show values of -1.58 and 33.6 that indicated a high instability in basin region. In addition, pressure synoptic analysis showed that 500 mb synoptic conditions are favorable for the occurrence of flooding is in accordance with expanding Atlantic – Europe down words polar shift. The dominant meridional pattern over the Mediterranean region and Middle East is formed over the Mediterranean and the West, with an intense fall over Iran. Bradbary and Radcliffe the indexes are fit for forecasting heavy rainfall that may lead to flooding.}, keywords = {Zayanderood Basin,Maximum Flood,Bradbury and Rackliff Indexes}, title_fa = {تحلیل ترمودینامیک و سینوپتیکی سیلاب‌های لحظه‌ای مناطق خشک (حوضه زاینده رود)}, abstract_fa = {بارش­های سنگین به دلیل نقشی که در رخداد سیلاب های بزرگ دارند از جمله عوامل موجد بحران محسوب می­شوند. بخش آبخیز حوضه سد زاینده رود (بالا دست سد)­ به عنوان مهم­ترین رودخانه مرکزی ایران با فراوانی بیشتر سیلاب­های بزرگ روبه­رو بوده است. سیلاب سال آبی 84-1383 با دبی 646 مترمکعب در ثانیه در 22/12/1383 با شاخص‌های استاندارد  47/10=SFI در حوضه مورد مطالعه رخ داده است. این سیلاب به عنوان بزرگ­ترین سیلاب ثبت شده  طی دوره آماری سال­های 88-1351 در حوضه سد زاینده رود برای بررسی انتخاب و جهت بررسی شرایط ترمودینامیکی و سینوپتیکی انتخاب گردید. بررسی متغیرهای هواشناختی و نمودارهای ترمودینامیکی نشان داد تغییرات دمای بالقوه­تر معیار مناسبی جهت شناخت شرایط توفان است. محاسبات ترمودینامیکی شاخص راکلیف با 6/33 درجه سلسیوس و شاخص برادباری با 58/1-  نشان دهنده شدت بارش های بالا درحوضه است. علاوه بر آن تحلیل همدید تراز 500 هکتوپاسکال نشان داد که شرایط مساعد ترمودینامیکی رخداد سیلاب با گسترش پر ارتفاع اقیانوس اطلس- اروپا به سمت قطب، حرکت تاوه قطبی به سمت عرض­های پایین، غالب شدن الگوی نصف النهاری بر روی منطقه مدیترانه و خاورمیانه و تشکیل فرازی در غرب مدیترانه، فرود عمیقی در شرق مدیترانه ، قرارگیری ایران در معرض وزش تاوایی مثبت و ورود سامانه های بارش زا به حوضه منطبق است. }, keywords_fa = {Zayanderood Basin,Maximum Flood,Bradbury and Rackliff Indexes}, url = {https://jise.scu.ac.ir/article_10788.html}, eprint = {https://jise.scu.ac.ir/article_10788_4f1ac233cd5426accc9e368d5b34691a.pdf} } @article { author = {Mahtabi, Ghorban and Hosseinzadehdalir, Ali}, title = {An Experimental Study of Current Deflecting Wall-Sill Effect on Sediment Control at Lateral Intake}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {69-81}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     Attention has been paid for many years to the problem of sedimentation in river intakes of irrigation and drainage projects, hydro-electric installations and water treatment plans. One of the methods to control sediment deposition at the entrance of intakes is the application of Submerged Vanes. But their efficiency is restricted to a particular hydraulic condition. In other word at the straight river reach, using submerged vanes in the low value of relative discharge (Qr<0.2) eliminates sediment uptake. Beyond this value, the effectiveness of the vanes reduces. The sediment-control performance of the vanes was enhanced by introducing different structures, modifying vane shape and changing intake geometry. In this research, Current Deflecting Wall-Sill (CDW-Sill) was used as a new method to control sediment at the lateral intake. The sediment-control performance of its various parameters was investigated. Primary and secondary CDW channel width, sill height and the angle of secondary CDW were also investigated using three different relative discharges. The results obtained showed that, when the angle of installation of the secondary CDW is 63 degree the sediment transport was low. The results also showed that up to relative discharge of 0.4, the primary CDW channel width equal to 14 cm has the best performance for different secondary CDW channel widths and eliminates sediment uptake. However increasing the Sill height reduces the performance of CDW-Sill. }, keywords = {Lateral intake,Sediment control,Current Deflecting Wall-Sill,Submerge Vanes}, title_fa = {مطالعه آزمایشگاهی اثر دیوار منحرف کننده جریان با آستانه در کنترل رسوب ورودی به آبگیر جانبی}, abstract_fa = {     مسئله کنترل فرسایش و رسوب­گذاری در دهانه آبگیر­های رودخانه برای شبکه­های آبیاری و زهکشی، نیروگاه­ها و تصفیه خانه­های آب از دیرباز مورد توجه بوده است. یکی از ایده­های جدید کنترل رسوب ورودی به آبگیر جانبی، استفاده از صفحات مستغرق می­باشد. یافته­های مطالعات نشان می­دهند که کارایی این صفحات محدود به شرایط خاص هیدرولیکی می­باشد یعنی در مسیرهای مستقیم این صفحات تا نسبت آبگیری 2/0 باعث حذف رسوب ورودی به آبگیر می­شود و برای مقادیر بیشتر نسبت آبگیری، کارایی صفحات کاهش می­یابد. راهکارهای افزایش کارایی این صفحات از طریق نصب سازه­های اضافی،‌ اصلاح دهانه آبگیر و شکل صفحات توسط محققین مختلف مورد بررسی قرار گرفته است. در این تحقیق با توجه به الگوی جریان در دهانه آبگیر، سیستم دیوار منحرف کننده جریان با آستانه به عنوان روشی جدید در کنترل رسوب ورودی به آبگیر با حفظ راندمان آبگیری، معرفی و تأثیر آن بر عملکرد آبگیر مطالعه شد. در این تحقیق عرض کانال دیوار منحرف کننده اولیه، عرض کانال دیوار منحرف کننده ثانویه ارتفاع آستانه و زاویه نصب دیوار منحرف کننده ثانویه بر روی رسوب ورودی به آبگیر در سه نسبت آبگیری مورد بررسی قرار گرفت. نتایج حاصل نشان داد در طرح اولیه دیوار منحرف کننده با آستانه با زاویه نصب 63 درجه برای دیوار منحرف کننده ثانویه رسوب کمتری وارد آبگیر شد. نتایج این تحقیق نشان داد تا نسبت آبگیری 4/0، عرض کانال دیوار منحرف کننده اولیه برابر 14 سانتی­متر به ازای تمام عرض­های کانال دیوار منحرف کننده ثانویه بهترین عملکرد را دارد و در این شرایط تقریباً رسوبی وارد آبگیر نشد. همچنین افزایش ارتفاع آستانه باعث کاهش عملکرد دیوار منحرف کننده شد.}, keywords_fa = {Lateral intake,Sediment control,Current Deflecting Wall-Sill,Submerge Vanes}, url = {https://jise.scu.ac.ir/article_10789.html}, eprint = {https://jise.scu.ac.ir/article_10789_2af49256a29d8187892510909f5f5248.pdf} } @article { author = {Salamatravandi, Hediyeh and Majdzadeh, Mohammadreza and Kharazifard, MohammadHossein and GhorbanBeigi, Saeid}, title = {Experimental Study of Soil Texture and Cross River Structures on Depth of Undercutting Hole Induced by Seepage Erosion in River Banks}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {83-93}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     Despite of many researches on bank erosion mechanism, there exists an incomplete understanding of one of the basic mechanisms governing sediment loading to streams which is namely erosion by concentrated lateral, subsurface flow which causes river bank failure after undercutting process and removing sediment into the river. The objective of this research is to study seepage erosion (piping) in river banks in two cases of presence of a cross structure (e.g. drainage pipes or gas transport pipes,…) and without cross structure by measuring the depth of undercutting hole induced by seepage erosion in sand layer with three different grain sizes under different hydraulic gradients in a laboratory flume. The results show that under equal hydraulic gradients length of erosion hole depends on river bank sand layer grain size and presence of cross structures.}, keywords = {Bank erosion,seepage erosion,piping,subsurface Flow,depth of undercutting hole,river bank,cross structure}, title_fa = {بررسی آزمایشگا‌هی تأثیر دانه‌بندی و وجود سازه‌های متقاطع بر عمق چاله‌ آبشستگی کناره رودخانه‌ها ناشی از فرسایش نشتی}, abstract_fa = {     علی­رغم پژوهش­های انجام شده بر روی مکانیزم فرسایش کناره رودخانه­ها، هنوز درک کاملی نسبت به فرآیند زیرشویی در تخریب کناره وجود ندارد. از آنجایی­که این تخریب باعث تخلیه­ رسوبات از لایه‌های کناری رودخانه­ها به داخل این مجاری می­شود و در نتیجه بر هیدرولیک و ریخت شناسی رودخانه تأثیر به سزایی دارد لذا فهم هر چه بهتر این فرآیند، امکان پایدارسازی را برای دست­اندرکاران ممکن می­سازد.  هدف این تحقیق مطالعه­ی فرسایش نشتی (جوشش) کناره‌‌‌ی رودخانه‌ها در دو حالت وجود و عدم وجود سازه­ی متقاطع (همچون لوله­ی زهکش یا لوله­ی انتقال گاز...) در لایه ماسه­ای با دانه بندی متفاوت در کناره­ی رودخانه می­باشد. بررسی­ها در یک مدل آزمایشگاهی و در گرادیان­های هیدرولیکی متفاوت با اندازه­گیری عمق چاله­ی آبشستگی ناشی از فرسایش نشتی در کناره (درون لایه­ی ماسه­ای) صورت گرفته است. نتایج بیان کننده­ی مؤثر بودن اندازه­ی ذرات و وجود سازه­ی متقاطع و گرادیان (ثابت در طول زمان متغیر) در چگونگی شکل­گیری فرسایش  می­باشد.  }, keywords_fa = {Bank erosion,seepage erosion,piping,subsurface Flow,depth of undercutting hole,river bank,cross structure}, url = {https://jise.scu.ac.ir/article_10790.html}, eprint = {https://jise.scu.ac.ir/article_10790_90b81a8f714f9b57ba21bcf876a8acfe.pdf} } @article { author = {Fathian, Farshad and Ahmadzadeh, Hojjat}, title = {Regional Flood Frequency Analysis Using L-Moments Based on Clustering in Urmia Lake Basin}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {95-106}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {For determining homogeneous regions and estimation of maximum flood in various return periods, cluster method and regional frequency analysis using linear moments are used in areas without hydrometric stations. Results showed that using Cluster analysis in the under study region was detected suitable to 5 homogeneous regions with k-means clustering method in Urmia lake basin. Discordance test has conducted and two stations such as Sahzab and Bokan were found as discordant stations and frequency analysis has implicated at-site. With elimination of discordant stations, all regions was found homogeneous using heterogeneity test. In this research, maximum annual flood fitted to eleven distribution functions. Using goodness-of-fit the Generalized logistic distribution were selected for three regions of A, B and C, Log normal 3 parameters for D, Generalized extreme value for E and for Sahzab and Bokan stations Log normal 2 and 3 parameters were chosen respectively. Besides, Generalized extreme value distribution was found appropriate for all of the regions.}, keywords = {Regional flood analysis,Clustering analysis,L-moments,Urmia Lake Basin}, title_fa = {تحلیل فراوانی منطقه‌ای سیلاب با استفاده از روش گشتاورهای خطی بر اساس تحلیل خوشه‌بندی در حوضه دریاچه ارومیه}, abstract_fa = {به منظور تعیین نواحی همگن و تخمین دبی­های حداکثر لحظه­ای با دوره بازگشت­های مختلف در نقاط فاقد ایستگاه­ آب­سنجی، از روش­ خوشه­بندی و تحلیل فراوانی منطقه­ای به روش گشتاورهای خطی استفاده شده است. نتایج تحلیل خوشه­بندی با روش K-means نشان داد پنج منطقه همگن در حوضه دریاچه ارومیه وجود دارد. با انجام آزمون­ ناجوری، ایستگاه­های سهزاب و بوکان ناجور بوده و پس از حذف به صورت ایستگاهی تحلیل فراوانی شدند.  آزمون­ ناهمگنی نیز تمامی نواحی را همگن تشخیص داد و برای تحلیل فراوانی این نواحی از 11 تابع توزیع احتمالی استفاده شد. بر اساس آزمون­های نکوئی برازش، توابع توزیع لجستیک تعمیم­یافته برای نواحی A، B و C، لوگ نرمال سه پارامتری برای ناحیه D، مقادیر حدی تعمیم­یافته برای ناحیه E و برای ایستگاه­های سهزاب و بوکان به ترتیب توابع لوگ نرمال دو و سه پارامتری انتخاب شدند. علاوه بر این، تابع توزیع مقادیر حدی تعمیم­یافته برای تمامی نواحی همگن مناسب تشخیص داده شد.}, keywords_fa = {Regional flood analysis,Clustering analysis,L-moments,Urmia Lake Basin}, url = {https://jise.scu.ac.ir/article_10791.html}, eprint = {https://jise.scu.ac.ir/article_10791_cd513a194add19735b88af5c736b1f6d.pdf} } @article { author = {Sadighkia, Mahdi and Ayoubzadeh, SeyedAli and Mamizadeh, Jaafar}, title = {An Experimental Study in the Effects of Non-uniform Particles of Sediment on the Progression and Pattern of Delta in Steady and Unsteady Flow}, journal = {Irrigation Sciences and Engineering}, volume = {35}, number = {3}, pages = {107-120}, year = {2012}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {Sedimentation occurs at the entrance of reservoir in the form of delta, and coarse particles create delta. In this research, the effect of non-uniformity of sediment particles on the progression and shape of delta in steady and unsteady flow is studied. Results show that in experiments with non-uniform particles, the progression of delta is more 2dimentional than in experiments with uniform sediment particles. Symmetry in final pattern of delta doesn’t depend on non-uniformity of sediment particles, and in all experiments a good symmetry can be observed. In experiments with non-uniform particles in steady flow, the power of Swenson equation for the toe is calculated 0.788 that shows slower progression for delta because this power in experiments with uniform particles is calculated 0.85. This is also correct in unsteady flow. After flood, the foreset slope of delta is decreased in experiments with non-uniform particles. }, keywords = {non-uniform particles,progression and pattern of delta,steady and unsteady flow}, title_fa = {بررسی آزمایشگاهی تاثیر وجود ذرات غیر یکنواخت رسوبی برروی پیشروی و شکل دلتا در جریان ماندگار و غیر ماندگار}, abstract_fa = {     رسوبگذاری به صورت دلتا در ورودی  مخزن اتفاق می‌افتد و ذرات درشت‌ دانه‌تر تشکیل دلتا را می‌دهند.  در این تحقیق تأثیر غیریکنواختی ذرات رسوبی برروی پیشروی و شکل دلتا در حالت ماندگار و غیرماندگار بررسی شده است. نتایج نشان می‌دهد که در آزمایش­هایی که از ذرات غیر یکنواخت در آنها استفاده شد حرکت دلتا نسبت به زمانی که از ذرات یکنواخت رسوبی استفاده شد دو بعدی­تر بود.  تقارن در شکل  نهایی دلتا به غیریکنواختی ذرات بستگی نداشته و در کلیه آزمایش­ها تقارن خوبی مشاهده گردید. در آزمایش­هایی غیر یکنواختی درحالت ماندگار، توان رابطه اسونسن برای پایه برابر 788/0 به دست آمد که با توجه به اینکه در حالت یکنواخت این توان برابر 85/0 بود حرکت کندتری برای دلتا نشان ‌داد که این مورد در جریان غیرماندگار نیز مشاهده ‌شد.  بعد از عبور سیلاب در  شیب پیشانی دلتا نیز در حالت وجود ذرات غیر یکنواخت کاهش بیشتری دیده ‌شد.  }, keywords_fa = {non-uniform particles,progression and pattern of delta,steady and unsteady flow}, url = {https://jise.scu.ac.ir/article_10792.html}, eprint = {https://jise.scu.ac.ir/article_10792_3327562aa6367ad6e7f3159ef2bd7d52.pdf} }