@article { author = {Goleaje, Hassan and Ghomeshi, Mehdi and Ahadian, Javad and Arjmandi, Hamed}, title = {Effect of Hydraulic and Geometric Parameters on Plunge Point in Density Current}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {1-9}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     When the dense flow mass intersect to stagnant fluid, dense flow penetrates into statically fluid and plunge depth occurs. In this research, hydraulic parameters of density current and bed slope have been investigated, which these have a considering effect on plunge point. To achieve on purposes of this research a physical model in hydraulic laboratory of Shahid Chamran University was built and various experiments were performed. At all of the experiment, plunge depth was measured in the various discharges of density current, different of density 6, 9, 13 and 16 kg/m3  at three slope 8, 12 and 16 percent. Then using Flow-3D depth of plunge point for these experimental conditions was simulated. Findings show that depth of plunge point derived with Flow-3D is more than measured values as in 12% slope, mathematical model overestimate about 30%. While, for all of the slope bed, simulated results 27 percent is more than corresponding measured values. Statistical evaluation shows that ratio of measured valued to results of Flow-3D is about 0.8. }, keywords = {Density current,Plunge point,Flow-3D,Physical model}, title_fa = {شبیه‌سازی تأثیر پارامترهای هیدرولیکی و ژئومتری بر نقطة غوطه‌وری در جریان‌های غلیظ}, abstract_fa = {در برخورد تودة جریان غلیظ با تودة سیال ساکن، جریان غلیظ به درون سیال ساکن نفوذ نموده و مکان غوطه‌وری ایجاد شده و عمق غوطه‌وری در بدو آن تشکیل می‌شود. با توجه به این‌که در محل غوطه‌وری مرز بین جریان غلیظ با سیال پیرامون مشخص می‌گردد، برآورد ارتفاع این نقطه از اهمیت به سزایی برخوردار است. در این تحقیق پارامترهای هیدرولیکی جریان غلیظ و همچنین شیب بستر سیال ساکن که بر نقطه غوطه‌وری تاثیر گذار است، بررسی شده است. برای نیل به اهداف این تحقیق ابتدا یک مدل فیزیکی در آزمایشگاه هیدرولیک دانشگاه شهید چمران ساخته شد و آزمایش‌های مختلف در آن انجام گردید. در تمامی آزمایش‌ها ارتفاع غوطه‌وری در دبی‌های مختلف از جریان غلیظ و تفاوت چگالی 6، 9، 13 و 16 کیلوگرم بر مترمکعب برای سه شیب 8، 12 و 16 درصد اندازه­گیری شد. سپس با استفاده از مدلریاضی Flow-3D ارتفاع نقطه غوطه‌وری برای شرایط آزمایشگاهی موجود شبیه‌سازی شد. بررسی مقایسه­ای نشان داد که عمق غوطه‌وری برآورد شده با استفاده از Flow-3D نسبت به مقادیر اندازه‌گیری شده بیشتر بوده به گونه‌ای که به طور متوسط برای شیب 12 درصد مدل ریاضی حدود 30 درصد نتایج را بیشتر پیش‌بینی نموده و این در حالی است که برای کلیه شیب‌ها به طور متوسط نتایج حاصل از مدل، 27 درصد بیشتر از مقادیر اندازه‌گیری شده می‌باشد. همچنین بررسی‌های آماری انجام شده نشان داد که نسبت مقادیر اندازه‌گیری شده به مقادیر پیش‌بینی شده به طور متوسط در حدود 8/0 می‌باشد.}, keywords_fa = {جریان غلیظ,نقطه غوطه‌وری,Flow-3D,مدل فیزیکی}, url = {https://jise.scu.ac.ir/article_10841.html}, eprint = {https://jise.scu.ac.ir/article_10841_1f0b3fc3585803367389290e1d757b4c.pdf} } @article { author = {Chitsazan, Manoochehr and Dehghani, Fatemeh and Mirzaee, SeyedYahya and Rastmanesh, Fatemeh}, title = {A Comparative Study of Analytical Hierarchy Process (AHP), Weighted Linear Combination (WLC) and Fuzzy Analytic Hierarchy Process (FAHP) Methods in Site Selection of Urban Waste Landfill (Case Study: Ramhormoz}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {11-21}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     One of the serious and growing potential in most large urban areas is the shortage of land for waste disposal. An inapproprriate landfill site may have negative enviromental, economic and ecological impacts. Therefore, it should be selected carefully by considering both regulations and constraints on there source. Choosing different factors leads to diversity in data layers and Geographic Information System (GIS) is very suitable due to the ability to manage huge volumes of data with different sources. The main aim of this research is to determine a suitable landfill site with less impact on environment For this purpose, the following data layers and maps have been utilized in this study, maps of slope, use land, soil, the depth of groundwater and the layers related to the distance from centers of waste generation (Ramhormoz), Population centers (village), surface water sources, underground water source (well, Spring), road network. The results of present research represents that the conditions in Analytical Hierarchy process(AHP) method has less certainty and the lack of definite limitations in this method, the sites selected according to Weighted Linear Combination(WLC) and Fuzzy-AHP (FAHP) have more parameters. However in studing the WLC and FAHP methods applied in this study, it was revealed that although WLC is simple, it has deficiencies; this method will locate many areas that may not be suitable, meanwhile FAHP, by ordered weights, offers this chance to the decision marker to include more important subjects which have greater role in site selection. Regarding to this ability, the result of site selection by FAHP has better resolution.}, keywords = {GIS,Ramhormoz,Analytical Hierarchy Process,Weighted Linear Combination,Fuzzy Analytic Hierarchy Process}, title_fa = {مقایسه روش‌های فرآیند سلسله مراتبی،ترکیب خطی‌- وزنی ، تحلیل فرآیند سلسله مراتبی فازی در مکان‌یابی محل مناسب جهت دفن پسماندهای جامد شهری (ناحیه مورد مطالعه: شهر رامهرمز)}, abstract_fa = {چکیده      یکی از پتانسیل های مهم و در حال رشد در بسیاری از مناطق بزرگ شهری، کمبود زمین برای دفع زباله می باشد. سایت های دفن زباله ممکن است دارای اثرات منفی اجتماعی، اقتصادی و زیست محیطی باشند. بنابراین لازم است این مناطق با در نظر گرفتن مقررات و محدودیت های موجود انتخاب گردند. انتخاب عوامل مختلف منجر به ایجاد تنوع از لایه اطلاعاتی می گردد. لذا سیستم اطلاعات جغرافیایی[1] با توجه به توانایی در مدیریت حجم عظیمی از داده ها با منابع مختلف برای این امر مناسب می باشد. هدف اصلی این تحقیق تعیین محل مناسب برای دفن زباله با تاثیر کمتر بر محیط زیست می باشد، لایه های اطلاعاتی و نقشه های مورد استفاده در این مطالعه شامل، نقشه های شیب، کاربری زمین، خاک، عمق آب زیرزمینی و لایه های مربوط به فاصله از مراکز تولید زباله (رامهرمز)، مراکز جمعیت (روستا)، منابع آب سطحی، منابع آب زیرزمینی (چاه، چشمه)، شبکه جاده ها می باشد. نتایج این تحقیق نشان داد که شرایط اعمال شده در روشفرآیند سلسله مراتبی[2]، با توجه به عدم محدودیت‌های قطعی که در آن اعمال می‌شود، از عدم اطمینان کمتری برخوردار می‌باشد و مناطق مکان یابی شده نسبت به روش‌های مبتنی بر منطقترکیب خطیوزنی[3] فرآیند سلسله مراتبی فازی[4]دارای تعداد پارامتر بیشتری می‌باشد. اما در بررسی ترکیب خطی-وزنی و فرآیند سلسله مراتبی فازی مشخص گردید که روش ترکیب خطی-وزنی علی رغم سادگی دارای معایبی می‌باشد، از جمله اینکه در این روش نسبت به فرآیند سلسله مراتبی فازی مناطق زیادی مکان یابی می‌گردند که ممکن است مناسب نباشد. منطق فرآیند سلسله مراتبی این قدرت را به تصمیم گیرنده می‌دهد که عوامل مهمتری را که از نظر کارشناسی وی مسئله مکان یابی را بیشتر تحت تاثیر قرار می‌دهند با همان اهمیت در مسئله قرار دهد. در اثر این برتری، نتیجه حاصل از مکان یابی به روش فرآیند سلسله مراتبی فازی دارای قدرت تفکیک بهتری بین طیف‌های موجود می‌باشد.}, keywords_fa = {سیستم اطلاعات جغرافیایی,رامهرمز,فرآیند سلسله مراتبی,ترکیب خطی-وزنی,تحلیل فرآیند سلسله مراتبی فازی}, url = {https://jise.scu.ac.ir/article_10842.html}, eprint = {https://jise.scu.ac.ir/article_10842_bfa466d0fb0a524f012e56bd21d4fc5b.pdf} } @article { author = {Izadinia, Elham and Heydarpoor, Manochehr}, title = {Investigation and Comparison of Efficiency of Cable and Groove in Protection Against Scouring}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {23-32}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {      Scouring around the bridge pier during the flood events threaten the bridge as important hydraulic structure.  Thus, designing the economical device in reducing the local scouring needs to be investigated. Cable has been introduced as new and economical countermeasure in local scouring. In the present study, different diameters and thread angles are studied through the experiments. In addition, groove is introduced in reducing the local scouring. The results show that with increasing cable diameter and decreasing thread angles the reduction of scour depth increases. The maximum scour reduction is achieved for pier protected with cable equal to 13% and 17% in front and behind of the pier respectively. While the groove is reduced scouring equal to 17% and 25% in front and behind of the pier respectively. Comparing the efficiency of cable with groove indicated that groove has higher efficiency in reduction of local scouring. }, keywords = {Scouring,Clear water,Equivalent time,Protection method,Cable Groove}, title_fa = {بررسی و مقایسه عملکرد کابل و شیار درکنترل آبشستگی پایه پل}, abstract_fa = {چکیده پل­ها از جمله مهمترین سازه­های هیدرولیکی هستند که آب­شستگی موضعی اطراف پایه­های آن­ها در طول جریان­های سیلابی یکی از عوامل تهدید پایداری آن­ها به شمار می­آید. بنابراین طراحی  پایه­ای که بتواند در شرایط بحرانی مقاومت نماید به گونه­ای که توجیه اقتصادی نیز به دنبال داشته باشد به تحقیقات گسترده­ای نیاز دارد. یکی از روش­های اقتصادی جدید مطرح شده در کنترل آب­شستگی پایه پل­ها استفاده از کابل پیچیده شده به دور پایه می­باشد. در مطالعه حاضر تأثیر زاویه پیچش کابل به دور پایه و تأثیر قطر کابل درکنترل و کاهش آب­شستگی بررسی و با نتایج دیگر محققین مورد مقایسه قرار گرفت. علاوه بر آن استفاده از شیارکه به صورت حلزونی به دور پایه پیچیده شده است به عنوان یک روش جدید در کنترل آب­شستگی پیشنهاد شده و عملکرد آن با کابل مورد مقایسه قرار گرفت. نتایج نشان داد با افزایش قطر کابل و کاهش زاویه پیچش، میزان آب­شستگی کاهش می­یابد، بیشترین میزان کاهش آب­شستگی برای پایه محافظت شده با کابل برابر 13 درصد و 17 درصد به ترتیب در جلو و پشت پایه به­دست آمد. این در حالی است که شیار میزان آب­شستگی را 17 درصد و 25 درصد به ترتیب در جلو و پشت پایه کاهش داد. بنابراین از مقایسه عملکرد کابل و شیار می­توان اذعان داشت میزان عملکرد شیار در کاهش آبشستگی بیشتر می­باشد.}, keywords_fa = {آب­شستگی,آب زلال,زمان تعادل,روش حفاظتی,کابل,شیار}, url = {https://jise.scu.ac.ir/article_10843.html}, eprint = {https://jise.scu.ac.ir/article_10843_2833e1878c3ee1bf670fe17463d3375e.pdf} } @article { author = {Khademi, Kheiralah and Shafaeebajestan, Mahmood and Ghomeshi, Mehdi}, title = {Flow Pattern Investigation at Bridge Abutment with and without Installed Submerged Vane}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {33-42}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     In this paper the results of measurement of three components of flow velocity around the bridge abutment with and without installed submerged vane are presented. Previous studies have shown that installation of submerged vane at the upstream corner of bridge abutment with angle of 40 degrees can decrease the scour depth. Plot of horizontal flow velocity components in different level, for both alternatives, with and without submerged vane, shows that the velocity vector at lower layer closed to the bed are shifted away from the abutment which causes that local bed shear stress are reduced and the scour at the vicinity of abutment reduced. The lower layer of stream lines are compressed at the edge of vane which cause scour at this location. It was proven that using submerged vane does not causes compression of the stream lines more than it usually occur due to abutment contraction. This means that the scour is shifted but the scour depth does not increase. Comparison of water surface profiles for with and without vane shows that the drop or lift of the water surface with vane is not significant and the change is in the safe way. Plot of vertical flow velocity vectors shows that the downward velocity has shifted from the abutment vicinity, in case of without vane, to the lower layers of the edge of submerged vane.}, keywords = {Submerged vane,Local scour,Erosion control,River,Abutment}, title_fa = {بررسی الگوی سرعت جریان در محل تکیه گاه پل در شرایط با و بدون نصب صفحه مستغرق}, abstract_fa = {     در این مقاله نتایج اندازه­گیری مؤلفه­های سه بعدی سرعت جریان در اطراف تکیه­گاه پل با و بدون نصب صفحه مستغرق ارائه شده است.مطالعات قبلی نشان داده است که نصب صفحه مستغرق در گوشه بالادست تکیه گاه با زاویه 40درجه می تواند کاهش دهنده عمق آبشستگی در اطراف تکیه­گاه باشدترسیم بردارهای افقی سرعت در رقوم های مختلف نشان داد که نصب صفحه مستغرق باعث می­شود تا خطوط جریان در لایه های پائینی از محل تکیه­گاه دور شود و این امر باعث کاهش شدید تنش برشی موضعی اطراف تکیه­گاه و در نتیجه کاهش عمق آبشستگی ­­گردد. فشرده شدن خطوط جریان در لبه­ی صفحه باعث افزایش تنش برشی موضعی در این مکان و در نتیجه افزایش عمق آبشستگی در اطراف صفحه می­شود.مقایسه بردارهای سرعت در دو حالت بدون و با صفحه نشان داد که صفحه مستغرق بر خلاف صفحه غیر مستغرق ،به استناد تحقیقات سایر محققین، باعث فشردگی خطوط جریان بیش از حد که تنگ شدگی اضافی در محل تکیه گاه بکند ایجاد نمی­کند و تغییرات تراز اندازه گیری شده سطح آب بسیار جزئی و در جهت محافظه کارانه است.ترسیم بردار­های مؤلفه عمودی سرعت نشان داد که مولفه عمودی رو به پائین از محدوده تکیه گاه در حالت بدون صفحه به لایه پائینی جریان در لبه صفحه منتقل شده است.}, keywords_fa = {صفحه مستغرق,آبشستگی,کنترل فرسایش,رودخانه,تکیه­گاه}, url = {https://jise.scu.ac.ir/article_10844.html}, eprint = {https://jise.scu.ac.ir/article_10844_4fe6ae7731ae87a605115ed4d3b56f83.pdf} } @article { author = {Babamiri, Omid and Dinpazhooh, Yaghoob}, title = {Comparison of Four Temperature Based Reference Crop Evapotranspiration Estimation Method at Urmia Lake Basin}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {43-54}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     The aim of this study is to compare and calibrate of four different temperature based  estimation methods in monthly time scale at Urmia Lake basin. The selected methods were Hargreaves (HG), Thornthwaite (TW), Blaney- Criddle (BC) and Linacre (Lin). For this purpose the information of weather parameters in the period 1986-2010 were used. Results of mentioned methods compared with the output of the FAO Penman- Monteith (PM56). Methods calibrated using the two distinct approaches. At first state only one calibration coefficient estimated along every year. At second state calibration coefficients estimated for each station and every month in a year. Performance of methods evaluated using the , RMSE, MBE and MAE statistics. The effectiveness of method’s calibration evaluated using the. Results showed that before calibration larger biases existed for selected methods comparing PM56. Calibration of methods considerably improved their performances. Results indicated that calibration of methods in the case of second state was very effective comparing the first state. The HG method was recognized as a best method either before or after calibration (in the first state) at the Urmia lake watershed. Linacre and Blaney- Criddle methods selected as the best methods following the Linacre method (after calibration at first state). Thornthwaite method had large error and therefore was not suitable method for estimation of  at the study area. The Linacre method was known as the best method of  estimation at Urmia Lake basin after calibration (at second state). HG, BC and TW were in the second to fourth rank orders, respectively.}, keywords = {Key words: Evapotranspiration,Urmia Lake Basin,Penman- Monteith,Hargreaves,Linacre,Blaney-Criddle,Thornthwaite}, title_fa = {مقایسه چهار روش‌ تخمین تبخیر و تعرق گیاه مرجع مبتنی بر درجه حرارت هوا در حوضه آبریز دریاچه ارومیه}, abstract_fa = {     هدف این مطالعه مقایسه و واسنجی چهار روش­ مختلف تخمین تبخیر- تعرق گیاه مرجع  مبتنی بر درجه حرارت هوا در مقیاس ماهانه در حوضه دریاچه ارومیه می­باشد. روش­های انتخاب شده شامل هارگریوز ، تورنت وایت ، بلانی کریدل  و لیناکر  بودند. برای این منظور از اطلاعات پارامترهای هواشناسی ده ایستگاه در دوره آماری 1986 تا 2010 استفاده شد. نتایج روش­های مذکور با خروجی روش فائو پنمن-مانتیث  مقایسه شدند. واسنجی روش­ها در دو حالت متمایز انجام شد. در حالت اول تنها یک ضریب واسنجی برای ایستگاه­ها تخمین زده شد. در حالت دوم ضریب واسنجی هر ایستگاه برای یکایک ماه­های سال محاسبه شد. ارزیابی روش­های مورد مطالعه با آماره­های ،RMSE ، MBEوMAE انجام شد. میزان اثر بخشی عمل واسنجی روش­ها با آماره  ارزیابی شد. نتایج نشان داد که قبل از واسنجی نتایج روش­های مختلف اختلاف زیادی با روش فائو پنمن-مانتیث داشت و واسنجی روش­ها در عملکرد آنها بهبود قابل ملاحظه­ای ایجاد کرد، همچنین نتایج نشان داد که واسنجی روش­ها در حالت دوم بسیار مناسب تر از حالت اول است. برای حوضه مورد مطالعه قبل و بعد از واسنجی (درحالت اول) روش هارگریوز به عنوان بهترین روش شناخته شد. پس از هارگریوز روش­­های لیناکر و بلانی­کریدل به ترتیب به عنوان روش­های مناسب تخمین تبخیر- تعرق گیاه مرجع (پس از واسنجی در حالت اول) تشخیص داده شدند. روش تورنت وایت خطای زیادی داشته و برای تخمین تبخیر- تعرق گیاه مرجع در منطقه مورد مطالعه مناسب تشخیص داده نشد. بعد از واسنجی (در حالت دوم) روش لیناکر به عنوان بهترین روش برای تخمین تبخیر- تعرق گیاه مرجعدر حوضه دریاچه ارومیه شناخته شد. روش­های هارگریوز، بلانی­کریدل و تورنت­وایت به ترتیب در رده­های دوم تا چهارم قرار گرفتند.}, keywords_fa = {تبخیر وتعرق,حوضه آبریز دریاچه ارومیه,پنمن- مانتیث,هارگریوز,لیناکر,بلانی­کریدل,تورنت­وایت}, url = {https://jise.scu.ac.ir/article_10845.html}, eprint = {https://jise.scu.ac.ir/article_10845_04bebbe303eff0ae6827cc561f23761b.pdf} } @article { author = {Asefi, Mehrnaz and Radmanesh, Fereydon and Zarei, Heydar}, title = {Optimization of DRASTIC Model for Vulnerability Assessment of Groundwater Resources Using Analytical Hierarchy Process (Case study: Andimeshk Plain)}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {55-67}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     Due to the increasing needs of human societies to groundwater supplies, the resource conservation and pollution prevention is necessary, especially in arid regions. Vulnerability assessment of groundwater can play a vital role in the protection of these resources. The main problem of DRASTIC model as the most widely used models for groundwater vulnerability assessment is the weighting. In this study, the weighting was modified using Analytical Hierarchy Process (AHP). To determine the optimal model, the correlation between the vulnerability index and the groundwater nitrate concentrations were determined using Simple Linear Regression Analysis (SLRA). The results showed that the optimal DRASTIC model has a better correlation rather than normal DRASTIC model. Also, to assess the risk of aquifer pollution, land use parameter added to the parameters and specific vulnerability aquifer map were prepared. The results showed that about 65 and 35 percent of Andimeshk aquifer contamination risk are very low and low, respectively.}, keywords = {Vulnerability,DRASTIC,Andimeshk plain,Analytical Hierarchy Process}, title_fa = {بهینه‌سازی مدل دراستیک در ارزیابی آسیب‌پذیری منابع آب زیرزمینی با استفاده از فرآیند تحلیل سلسله مراتبی (مطالعه موردی: دشت اندیمشک)}, abstract_fa = {چکیده      با توجه به نیاز روز افزون جوامع بشری به منابع آب زیرزمینی به ویژه در مناطق خشک، حفاظت و جلوگیری از آلودگی این منابع امری ضروری می‌باشد. ارزیابی آسیب‌پذیری آب‌های زیرزمینی نقش حیاتی در حفاظت و بهره‌برداری از این منابع دارد. یکی از متداول­ترین مدل‌های ارزیابی آسیب‌پذیری آب‌های زیرزمینی، مدل دراستیک است. سلیقه‌ای بودن نرخ‌بندی پارامترهای به کار رفته در این مدل، مشکل اصلی آن به شمار می­رود. در مطالعه حاضر، وزن‌دهی پارامترهای مدل دراستیک با روش تحلیل سلسله مراتبی (AHP) اصلاح گردید. جهت تعیین مدل بهینه، ضریب همبستگی بین شاخص آسیب­پذیری و غلظت نیترات آب زیرزمینی با استفاده از روش تحلیل رگرسیون خطی ساده محاسبه گردید. نتایج این تحلیل نشان داد که مدل دراستیک بهینه نسبت به مدل دراستیک نرمال از همبستگی بهتری با غلظت نیترات برخوردار می‌‌باشد. همچنین برای ارزیابی خطرپذیری آبخوان به آلودگی، پارامتر کاربری اراضی به پارامترهای قبلی افزوده و بدین ترتیب نقشه آسیب­پذیری ویژه آبخوان تهیه گردید. نتایج حاصل نشان داد که حدود 65 درصد از آبخوان دشت اندیمشک از خطرپذیری آلودگی خیلی کم و 35 درصد مابقی، دارای خطرپذیری آلودگی کم می‌باشد.}, keywords_fa = {آسیب­پذیری,دراستیک,دشت اندیمشک,تحلیل سلسله مراتبی}, url = {https://jise.scu.ac.ir/article_10846.html}, eprint = {https://jise.scu.ac.ir/article_10846_a828bce1f8a0e0676c6057d210e24b38.pdf} } @article { author = {Tangsir, Sareh and Izadpanah, Zahra and Kashkoli, Heydarali and Moazed, Hadi}, title = {Estimation of Philip Equation Sorptivity Factor by Two Methods Using Disc Permeameter}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {69-80}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {Determination of unsaturated soil hydraulic parameters are important for assessment and understanding of many processes. These processes include as: runoff and rainfall infiltration, salt, contaminations and nutrition elements transmission in soil and solution absorption by plant root. Recently, disc permeameter has been recognized as one of most current tool for measurement of unsaturated soil surface hydraulic parameters. In this research, for study of relation between unsaturated soil hydraulic conductivity and sorptivity curve,the field experiments were performed at six iterations to interval of 1 meter each other on three zons (first zone with silty loam texture, second and third zone with loam texture). At all iterations, steady infiltration rates were measuremented on soil surface in consective five suctions, 15, 10, 6, 3 and 0 cm recpectively. Then,  sorptivity factors in each suction were estimated by methods of differentiation (unsteady analysis) and steady analysis. The results of this study indicated that, sorptivity curve (s(h)) similar as unsaturated hydraulic conductivity curve (k(h)) is followed an exponential function. Sorptivity factor had inverse relation with suction, so that sorptivity value increased with suction reduction. Also, the results of this study showed that unsteady analysis method estimate sorptivity value at all suctions more than steady analysis method and the differences are significant in suctions of 3 and 0 cm. The study results indicated soil sorptivity factor inverse relationship with α parameter and α parameter inverse relationship with soil structure resistance degree. Also, it is observed that sorptivity factor sensitivity to soil structure is more than hydraulic conductivity.}, keywords = {Key words: Disc Permeameter,Unsaturated hydraulic conductivity,Sorptivity factor,Philip Equation,α parameter}, title_fa = {تخمین ضریب جذب معادله فیلیپ به دو روش با استفاده از نفوذسنج دیسک}, abstract_fa = {     تعیین خصوصیات هیدرولیکی خاک غیراشباع، در تشخیص و فهم بسیاری از فرآیندها بسیار مهم می­باشد.ازآن جمله می­توان به نفوذ رواناب، بارندگی، انتقال املاح، آلودگی­ها و مواد غذایی در خاک و جذب املاح توسط ریشه گیاه اشاره نمود. به تازگی دستگاه نفوذسنج دیسک به عنوان یکی از رایج­ترین ابزار اندازه­گیری صحرایی خصوصیات هیدرولیکی سطحی خاک غیراشباع شناخته شده است. در این تحقیق،  به منظور بررسی رابطه بین منحنی جذب و هدایت هیدرولیکی غیر اشباع  خاک آزمایش­های صحرایی در شش تکرار به فواصل یک متر از همدیگر در سه ناحیه (ناحیه اول با بافت سیلتی لوم و ناحیه دوم و سوم با بافت لوم) انجام گرفت. در کلیه تکرارها، سرعت­های نفوذ پایدار در سطح خاک درپنج مکش متوالی 15، 10، 6، 3 و صفر سانتی­متر اندازه­گیری شد. سپس جهت تخمین ضریب جذب در همان مکش­ها، از روش مشتق­گیری (تحلیل ناپایدار) و تحلیل پایدار، استفاده گردید. نتایج این تحقیق نشان داد که منحنی جذب(S(h))، همانند منحنی هدایت هیدرولیکی غیراشباع)(k(h)، از یک تابع نمایی تبعیت نموده و این فاکتور با مکش رابطه­ی عکس دارد به طوری که با افزایش فشار (کاهش مکش)، میزان جذب افزایش می­یابد. همچنین مشاهده شدکه روش تحلیل ناپایدار مقادیر جذب را در تمامی مکش­ها بیشتر از روش تحلیل پایدار تخمین می­زند و این تفاوت­ها در مکش­های 3- و صفر سانتی­متر معنی­دار است. نتایج این تحقیق بیانگر رابطه­ی عکس فاکتور جذب خاک با پارامتر α و رابطه­ی عکس پارامتر α با درجه استحکام و پایداری ساختمان خاک می­باشد. هم چنین مشاهده شد که حساسیت فاکتور جذب به ساختمان خاک بیشتر از هدایت هیدرولیکی می­باشد. }, keywords_fa = {نفوذسنج دیسک,هدایت هیدرولیکی غیراشباع,ضریب جذب,معادله فیلیپ,پارامتر α}, url = {https://jise.scu.ac.ir/article_10847.html}, eprint = {https://jise.scu.ac.ir/article_10847_609575bd33abc0b22271103efd0eabd5.pdf} } @article { author = {Asareh, Ali and Derakhshannezhad, Zahra and Soltanimohammadi, Amir and Gosheh, Mahialdin}, title = {Simulation of Soil Moisture by HYDRUS-1D Model under Wheat Cultivation}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {81-92}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {   To achieve the goal of high yield, deep understanding of physiological, agronomic and environmental factors is necessary to improve the performance and sustainability of agricultural systems. This may not be practical unless the plant complex systems and the type of response to inputs and environmental conditions are known as important factors. In modern agricultural methods the uses of different models are important for management, optimize productivity, accurate understanding of the system and obtaining a precise formulation of the standard.  In order to simulation of soil moisture under different water conditions on wheat(Chamran cultivar) a field experiment was conducted at the Agricultural Research Center- Ahwaz. In this experiment, three irrigation levels include I1 ( no water stress ), I2 (stop irrigation at the heading  stage and I3(stop  irrigation  at the milky grain stage) and five levels of  nitrogen fertilizer namely  N1(no nitrogen fertilizer), N2=40, N3=80, N4=120 and N5=160 kg/ha were used as treatments. In this research, HYDRUS-1D was used as simulation model. Analysis of results for sensitivity of model showed that soil moisture coefficient of model under saturation condition θs is more than other coefficients and a slight change in coefficient caused a large change in output variation of model. The minimum effect was observed in α, I and θr coefficients. Meanwhile, results indicated that model was estimated moisture content less than reality condition. Also, the amount of moisture on the basis of simulated model was estimated less than the real moisture. The model efficiency that reflects to quality and observed data was estimated between 0.67 and 0.90. This was due to high efficiency of simulated model for soil moisture.}, keywords = {Siimulation,Moisture,Model,wheat,HYDRUS-1D}, title_fa = {شبیه سازی رطوبت خاک با مدل HYDRUS-1D در شرایط کشت گندم}, abstract_fa = {     برای دستیابی به افزایش عملکرد، شناخت عمیق عوامل محیطی جهت حفظ یا افزایش بهره‌دهی و پایداری سیستم­های کشاورزی ضرروی است و این مهم عملی نخواهد شد مگر آنکه سیستم پیچیده گیاه و نوع پاسخگوئی آن به نهاده‌ها و شرایط محیطی تا اندازه زیادی شناخته شود. از روش­های نوین کشاورزی که در امر تحقیق، مدیریت، بهینه کردن بهره‌وری، شناخت کامل سیستم و تدوین یک استاندارد دقیق برای آن بسیار مؤثر است، بهره‌گیری از مدل‌های مختلف می‌باشد. به منظور شبیه سازی رطوبت خاک تحت شرایط مختلف آبی، تحقیقی در مزرعه مرکز تحقیقات کشاورزی اهواز  در سال زراعی 85-1384بر روی گیاه گندم با سه تیمار آبیاری I1 (بدون تنش آبی)، I2 (قطع آبیاری در مرحله ظهور سنبله) و I3 (قطع آبیاری در مرحله شیری شدن دانه) و پنج سطح نیتروژن با مقادیر   N1(بدون مصرف کود نیتروژن) ‌= N2، 80= N3 ، 120= N4، 160= N5 کیلوگرم در هکتار انجام شد. برای شبیه‌سازی رطوبت در خاک از مدل HYDRUS-1D  استفاده گردید. نتایج تحلیل حساسیت مدل نشان داد که مدل نسبت به ضریب رطوبتی خاک در حالت اشباع (θs)بیش از دیگر ضرایب حساس است و با تغییر جزئی مقادیر این ضریب تغییرات به سزایی در خروجی­های مدل مشاهده شد.  کمترین تأثیر مربوط به ضرایب α، I وθrبود .همچنین نتایج آزمایش نشان داد مدل مقدار رطوبت را کمتر از واقعیت برآورد می کند. مقدار کارایی مدل که نشان دهنده کیفیت و چگونگی برازش داده‌های مشاهده‌ای و برآورد شده می‌باشد بین 67/0 تا 90/0 متغیر بود که این نشان دهنده کارایی بالای  مدل در شبیه سازی رطوبت است.}, keywords_fa = {شبیه سازی,رطوبت,مدل,گندم,HYDRUS-1D}, url = {https://jise.scu.ac.ir/article_10848.html}, eprint = {https://jise.scu.ac.ir/article_10848_43012acca34c584a0cc235f809d94363.pdf} } @article { author = {Ahmadi, Farshad and Dinpazhooh, Yaaghob and Fakherifard, Ahmad and Khalili, Keyvan}, title = {Comparing Linear and Nonlinear Time Series Models in River Flow Forecasting (Case Study: Baranduz-chai River)}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {93-105}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     Forecasting river flow using current models like time series, Physical-theoretical and regression models are very important in water resources management. In this study monthly and daily discharge of Barandouz-Chai River for period of 37 years have been used in order to linear ARMA and Nonlinear Bilinear models. ADF test has been used for stationarity test. Result showed removing nonstasionarity components cause to river series became stationary. For nonlinearity rate of monthly and daily streamflow series BDS test has been employed. As results showed monthly series detect low nonlinearity but daily series has high nonlinearity dependence. For monthly series AR(8) and BL(8,0,1,1) selected as the best models. Regression coefficient and root mean square error of these models are 0.906 and 2.892 (m3/s) for linear model and 0.930 and 2.436 (m3/s) for nonlinear model respectively. For daily streamflow series, AR(25) and BL(25,0,1,1) were best models with regression coefficient and root mean square error equal to 0.873 and 4.116 (m3/s) for linear model and 0.923 and 3.085 (m3/s) for nonlinear model respectively. According to results using bilinear nonlinear model cause to reduction error of daily model up to 33 percent and increased regression coefficient to 5.7 percent. Because of high nonlinearity rate of daily streamflow series the bilinear model accuracy increased.}, keywords = {ADF test,BDS test,Stationarity,Time series,Bilinear Model}, title_fa = {مقایسه مدل‌های خطی و غیرخطی سری‌زمانی در پیش‌بینی جریان رودخانه (مطالعه موردی: رودخانه باراندوزچای ارومیه)}, abstract_fa = {     پیش­بینی دقیق جریان رودخانه­ با استفاده از مدل­های رایج سری­های زمانی، فیزیکی- مفهومی و رگرسیونی در مدیریت علمی منابع آب­های سطحی اهمیت به­سزایی دارد. در این مطالعه دبی جریان روزانه و ماهانه رودخانه باراندوزچای ارومیه در دوره­ آماری 88-1352، با استفاده از مدل­های سری­زمانی خطی آرما[1] و غیرخطی دوخطی مدل­سازی شد. برای بررسی ایستایی سری­های جریان از آزمون ADF استفاده گردید. نتایج آین آزمون نشان داد که با حذف عوامل ناایستایی، سری­های جریان رودخانه ایستا می­شوند. برای بررسی شدت غیر خطی بودن سری­های ماهانه و روزانه جریان از آزمون BDS استفاده شد. نتایج نشان داد که سری ماهانه جریان، خاصیت غیرخطی خفیفی دارد اما سری روزانه جریان به شدت غیر خطی می­باشد. مدل­های AR(8) و BL(8,0,1,1) مدل­­های منتخب جریان ماهانه بوده که ضریب همبستگی و جذر میانگین مربعات خطا در مدل خطی به ترتیب 906/0 و 892/2 مترمکعب در ثانیه و برای مدل غیرخطی 930/0 و 436/2 متر مکعب در ثانیه محاسبه گردیدند. برای جریان روزانه، مدل خطی AR(25) و مدل غیرخطی BL(25,0,1,1) انتخاب گردید که ضریب همبستگی و جذر میانگین مربعات خطا در مدل خطی به ترتیب برابر 873/0 و 116/4 متر مکعب در ثانیه و برای مدل غیرخطی معادل 923/0 و 085/3 متر مکعب در ثانیه به دست آمد. طبق نتایج حاصله، استفاده از مدل دوخطی در مقیاس روزانه سبب کاهش مقدار خطا به میزان 33 درصد شد و ضریب همبستگی را 7/5 درصد افزایش داد. افزایش دقت مدل دوخطی در مقایسه با مدل خطی به دلیل خاصیت غیرخطی شدید مقیاس روزانه می­باشد.}, keywords_fa = {آزمونADF,آزمونBDS,ایستایی,سری­زمانی,مدل دوخطی}, url = {https://jise.scu.ac.ir/article_10849.html}, eprint = {https://jise.scu.ac.ir/article_10849_840c0cd04f26f79042d09332a5acb7c5.pdf} } @article { author = {Poorsalehan, Seyedjamal and Sedghiasl, Mohammad and Parvizi, Mansoor}, title = {Application of The Wetted Perimeter Method for Predicting Minimum Environmental flow of Beshar River}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {107-118}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     Minimum environmental flow in rivers provides a certain level of protection for the aquatic environment. In Iran using hydraulic method of wetted perimeter could be a step forward in this field. How to identify the critical point in P-Q curve is still faced with uncertainty in this method. Slope, Curvature and Ideal Point Methods presented by different researchers in this filed. In this article beside description of wetted perimeter method, the environmental flow of Beshar River calculated by using hydraulic parameters. The average of results of Slope, Curvature and Ideal Point Methods is 23%, 8.4% and 20.6% of average annual flow of river, respectively. The results of Slope and Ideal Point Methods are in the acceptable rang of the Tennant method. But the Ideal Point method is superior choice due to the direct use of the chart and more rapidly in calculation.}, keywords = {Keywords: Environmental flow,Beshar river,Wetted perimeter method,Critical point,Ideal point method}, title_fa = {استفاده از روش محیط خیس شده برای برآورد حداقل جریان زیست محیطی رودخانۀ بشار}, abstract_fa = {     حداقل جریان زیست محیطی در رودخانه سطح مطمئنی از حفاظت را برای محیط زیست وابسته به آب تهیه می‌کند. در کشور ما استفاده از روش هیدرولیکی محیط خیس شده می‌تواند گامی رو به جلو در این زمینه باشد. در این روش نحوۀ تشخیص نقطۀ بحرانی در منحنی دبی-محیط خیس شده همچنان با ابهاماتی رو به رو است. در این زمینه روش­های شیب، انحنا و نقطه ایده‌آل توسط محققین مختلف ارائه شده است. در مقالۀ حاضر ضمن بیان روش محیط خیس شده، جریان زیست محیطی رودخانۀ بشار با استفاده از پارامترهای هیدرولیکی محاسبه گردید. متوسط نتایج روش­های شیب، انحنا و نقطه ایده‌آل به ترتیب معادل 23 درصد، 4/8 درصد و 6/20 درصد متوسط جریان سالانۀ رودخانه است. نتایج روش‌های شیب و نقطه ایده‌آل در محدودۀ قابل قبول حاصل از نتایج کار تنانت قرار گرفتند ولی روش نقطۀ ایده‌آل به دلیل استفادۀ مستقیم از نقاط نمودار و سرعت بیشتر در محاسبات به عنوان روش برتر انتخاب شد.}, keywords_fa = {جریان زیست محیطی,رودخانۀ بشار,روش محیط خیس شده,نقطۀ بحرانی,روش نقطه ایده‌آل}, url = {https://jise.scu.ac.ir/article_10850.html}, eprint = {https://jise.scu.ac.ir/article_10850_ab40a387b81a1bd3e69d2b19e1b1733e.pdf} } @article { author = {Abedikopaee, Jahangir and Mousavi, Seyedfarhad and Rahmani, Mahsa}, title = {Effect of Wood, Sand, and Tire Chips Mulches on Evapotranspiration Using ZFP Model}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {119-131}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     One method of determining evapotranspiration is zero flux plane (ZFP). This method estimate the evapotranspiration based on water content and soil suction. This method can also estimate the value of evaporation, evapotranspiration and ground water recharge. The data used in this study were obtained from a field experiment at Isfahan University of Technology. The experiment was factorial design [3×8] in the basic design of randomized complete blocks that the first factor was the types of mulch and the second factor was the depth of soil mulch. The field trial was conducted for 44 days. Results obtained from the ZFP model was compared with Ref-ET and OPTIWAT models. The experiment consisted of wood, sand and tire chips mulches with 2.5 and 5 cm thickness in the plots. Three plots were planted with grass and three plots left uncovered. The results showed that the depth of  ZFP varied in different mulches. The highest ZFP depth was related to the uncovered plot and the lowest ZFP depth was related to the plot with 5 cm sand thickness. the results indicated  that the experiment plot with no mulch had the greatest evapotranspiration (178 mm) and then woody chips mulch with a thickness of 5 cm, tire chips mulch with a thickness of 5 cm, tire chips mulch with a thickness of 2.5 cm, sandy mulch with a thickness of 2.5 cm, the woody chips mulch with a thickness of 2.5 cm and sandy mulch with a thickness of 5 cm, had more evapotranspiration, respectively. the results showed that the amount of evapotranspiration obtained by the ZFP model with the results of the Ref-ET and OPTIWAT model, were different. Ref-ET and OPTIWAT models under-estimated the actual evapotranspiration obtained by ZFP. In Ref-ET model, the equation of modified Blany-Cridle had the closest estimation (159 mm) to the evapotranspiration determined by ZFP model. In OPTIWAT model, the modified Jensen-Haise method had the nearest estimation (161.4 mm) to the ZFP model.}, keywords = {Evaporation,Transpiration,Zero flux plane,Mulch}, title_fa = {تخمین تبخیر و تعرق از پروفیل خاک در حضور مالچ های چوبی، سنگی و تراشه های لاستیکی به روش سطح شار صفر}, abstract_fa = {     یکی از روش­های تعیین تبخیر و تعرق روش سطح شار صفر است که بر اساس رطوبت و مکش موجود در خاک، تبخیر و تعرق را تخمین می­زند. از این روش در اندازه­گیری و تخمین مقدار تبخیر، تبخیر و تعرق و تغذیه آب زیرزمینی استفاده می­شود. در این تحقیق که در مزرعه تحقیقاتی دانشگاه صنعتی اصفهان انجام شد، از انواع مالچ­های چوبی، سنگی و تراشه­های لاستیکی با ضخامت­های 5/2 و 5 سانتی­متر در مقایسه با چمن و خاک بدون پوشش به منظور تأثیر در میزان تبخیر و تعرق از پروفیل خاک توسط مدل مزرعه ای سطح شار صفر، به صورت طرح فاکتوریل (38) در قالب طرح پایه بلوک­های کامل تصادفی که فاکتور اول شامل انواع مالچ، چمن و تیمار بدون پوشش و فاکتور دوم عمق خاک بود استفاده شد. مدت انجام آزمایش­های مزرعه­ای 44 روز بود و همچنین نتایج روش مذکور در مقایسه با مدل­های کامپیوتری  Ref-ETو OPTIWAT مورد بررسی قرار گرفت. نتایج نشان داد عمقی که سطح شار صفر در آن تشکیل می­گردد در حضور مالچ­های مختلف متفاوت است. بیشترین عمق سطح شار صفر در کرت بدون پوشش در 38 سانتی­متری از سطح خاک و کمترین عمق در 32 سانتی­متری از سطح خاک در کرتی تشکیل گردید که پوشش سنگی به ضخامت پنج سانتی­متر داشت. طبق معادله­های روش سطح شار صفر، در طول آزمایش، کرتی که بدون پوشش بود بیشترین میزان تبخیر و تعرق (178 میلی­متر) را داشت و پس از آن به ترتیب چمن، مالچ چوبی به ضخامت 5 سانتی­متر، مالچ لاستیکی به ضخامت 5 سانتی­متر ، مالچ لاستیکی به ضخامت 5/2 سانتی­متر ، مالچ سنگی به ضخامت 5/2 سانتی­متر ، مالچ چوبی به ضخامت 5/2 سانتی­متر و مالچ سنگی به ضخامت 5 سانتی­متر بیشترین میزان تبخیر و تعرق را داشتند. نتایج مقایسه روش سطح شار صفر  با دو مدل Ref-ET و OPTIWAT نیز نشان داد که مقدار تبخیر و تعرق به دست آمده در کرت بدون پوشش توسط روش سطح شار صفر (178 میلی­متر) که در آن از پارامترهای خاک استفاده شده، با نتایج مدل‌های Ref-ET و  OPTIWAT که از پارامترهای هواشناسی در آنها استفاده گردیده، تفاوت دارد. در مدل Ref-ET میزان تبخیر و تعرق به دست آمده توسط روش بلانی- کریدل اصلاح شده (159میلی­متر) و در مدل OPTIWAT روش جنسن- هیز اصلاح شده (4/161 میلی­متر) نزدیک­ترین مقدار به تبخیر و تعرق محاسبه شده توسط روش سطح شار صفر را داشتند.}, keywords_fa = {تبخیر,تعرق,سطح شار صفر,مالچ}, url = {https://jise.scu.ac.ir/article_10851.html}, eprint = {https://jise.scu.ac.ir/article_10851_091a741512a5cb070578551d86385a41.pdf} } @article { author = {Omidvarinia, Mona and Mousavijahromi, Seyedhabib}, title = {Comparative Analysis of energy Losses in the Traditional and Triangular Flip Buckets}, journal = {Irrigation Sciences and Engineering}, volume = {37}, number = {1}, pages = {133-142}, year = {2014}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {}, abstract = {     In this study the triangular flip bucket instead of circular shaped- with the same character but with different geometries- was studied. In this regard, the performance hydraulic overflow bucket with a bucket instead of the usual triangular shape, were compared in terms of energy dissipation. In this regard, the hydraulic performance triangular shaped bucket instead of the usual bucket, were compared in terms of energy dissipation.To achieve this goal, a physical model of the ogee spillway was built in the hydraulic physical models laboratory of Shahid Chamran University (SCU) and experiments were performed in 4 discharges that followed by four different Froude number. The for each discharge 3 tail-water depth were used to run experiments. The results showed that in comparison to the Total performance energy dissipation in triangle flip bucket with 45-degree angle insignificantly is better than cup flip bucket. For example, energy dissipation in Froude number 3.13 in the case of the free jet in the triangle and cup flip bucket respectively 66.4 and 54.8 percent. The lowest and most energy dissipation respectively related to triangle flip bucket with 22.5-degree angle and Triangle flip bucket with 45-degree angle with 7 cm approach channel. A comparison with results for the circular shaped bucket geometry indicates a favorable behavior of the novel bucket design.  }, keywords = {Flip Buckets,Triangular Flip Buckets,Energy Losses,Physical model}, title_fa = {مقایسه تلفات انرژی در پرتاب کننده‌های جامی دایره‌ای و مثلثی شکل}, abstract_fa = {چکیده در این تحقیق پرش اسکی نوع مثلثی که دارای ماهیتی مشابه سرریزهای جامی شکل، ولی با هندسه متفاوت است، مورد بررسی قرار گرفته است. در این راستا عملکرد هیدرولیکی سرریز با باکت مثلثی شکل به جای باکت دایره‌ای، از نظر میزان اتلاف انرژی جنبشی مورد مقایسه قرار گرفت. برای نیل به اهداف این تحقیق، یک مدل فیزیکی از سرریز اوجی در آزمایشگاه مدل‌های فیزیکی هیدرولیکی ساخته شد و در چهار دبی و به دنبال آن در اعداد فرود مختلف آزمایش‌ها انجام شد. همچنین برای هر دبی، 3 عمق پایاب به کار گرفته شد؛ به طوری‌که، در هر حالت پرتاب کننده دایره‌ای و مثلثی با زوایای مختلف منظور گردید. نتایج نشان داد که در حالت مقایسه کلی عملکرد پرتاب کننده مثلثی 45 درجه به طور قابل توجهی در استهلاک انرژی بهتر از پرتاب کننده جامی می‌باشد؛ به طور مثال، برای عدد فرود 13/3 در حالت جت آزاد این مقدار در پرتابه‌ی مثلثی و جامی به ترتیب 4/66 و 8/54 درصد می‌باشد. کمترین درصد استهلاک انرژی برای پرتاب کننده مثلثی با زاویه 5/22 درجه و بیشترین استهلاک انرژی در پرتاب کننده مثلثی با زاویه 45 درجه و طول دسترسی 7 سانتی متر می‌باشد. در حالت مثلثی شکستگی خطوط جریان در برخورد با شیب مثلث رخ داده و این در حالی است که برای حالت معمولی این شکستگی به مراتب کمتر است. در نهایت با توجه به هندسه و اجرای راحت‌تر پرتاب کننده‌های مثلثی و عملکرد بهتر آن در میزان استهلاک انرژی استفاده از این نوع پرتاب کننده توصیه می‌شود.}, keywords_fa = {پرتاب‌کننده‌های جامی,پرتاب‌کننده‌های مثلثی,استهلاک انرژی,مدل فیزیکی}, url = {https://jise.scu.ac.ir/article_10852.html}, eprint = {https://jise.scu.ac.ir/article_10852_317a9c76adc2647515b802375f845df4.pdf} }