@article { author = {Asghari Pari, Seyed Amin and Kashefi Pour, Seyed Mahmood and Ghomeshi, Mehdi}, title = {Experimental investigation on controlling of sedimentary density current using constructing obstacle}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {1-15}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13475}, abstract = {Density currents are the main cause for sediment transport in dams reservoirs and seas deltas. One of the problem solution is to reduce or eliminate the effect of them using completely block the density current and as a result the sediment settle far away from the dam in strolling of density current, some experiment were carried out on a flume in water Sciences Engineering Laboratory, Shahid Chamran University of Ahwaz. In this research density current were provided using sediments with d50 of 28.9 µm and passing flow from obstacle was investigated under different bed slopes and discharges. The obtained results show that the effect of obstacle for sub-critical flow is more than supercritical flow. However it was found that even for supercritical flow obstacles are considerably effective on preventing of density current flow.}, keywords = {Density current,Sediment transport,dam reservoirs,seas deltas}, title_fa = {بررسی آزمایشگاهی کنترل جریان غلیظ رسوبی به کمک احداث مانع}, abstract_fa = {جریان‌های غلیظ از جمله عوامل مهم در انتقال رسوبات به مصب دریاها و مخازن سدها می‌باشند. یکی از روش‌های کاهش و یا حذف اثر این جریان استفاده از مانع در مسیر آن‌ها می‌باشد. مانع می‌تواند جلوی بخشی و یا تمام جریان غلیظ را سد نماید و در نتیجه رسوبات در مناطق دورتری نسبت به تاسیس مهمی مانند سدها ته نشین گردند. به منظور بررسی اثر مانع بر روی کنترل جریان غلیظ، آزمایشات در یک فلوم آزمایشگاهی انجام پذیرفت. در این تحقیق جریان غلیظ به کمک رسوبات با d50، 7/29 میکرومتر تهیه و شرایط جریان عبوری از مانع در دبی‌ها و شیب‌های مختلف بررسی گردید. نتایج نشان می‌دهد با وجود اینکه اثر مانع در جریان زیر بحرانی بیشتر از جریان فوق بحرانی است لیکن وجود. مانع می‌تواند تأثیر نسبتاً قابل ملاحظه‌ای بر روی دبی رسوبی عبوری از مانع حتی در جریان‌های فوق بحرانی داشته باشد.}, keywords_fa = {Density current,Sediment transport,dam reservoirs,seas deltas}, url = {https://jise.scu.ac.ir/article_13475.html}, eprint = {https://jise.scu.ac.ir/article_13475_f6eb13eb916813a59618826e9d9f08d0.pdf} } @article { author = {rikvaandi, Khosro and Masjedi, Alireza and Bina, Mahmood}, title = {Determiation of friction factor in river banks and floodplains with non-submerged vegetation}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {17-28}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13476}, abstract = {   Because of vegetation flexibility in flood plains and river banks, friction factors vary in these areas and are function of vegetation characteristics and flow conditions. Due to being of  important structures such as water pumping stations, Roads, water treatment plans and wastewater,  fish pools in the river banks and construction of structures such as bridges and diversion dams on them, study of river behavior especially effect of vegetation on flow capacity is very important. Purpose of this research was to obtain relationships and values suitable for vegetation roughness coefficients in the flood plains and river banks for Non-submerged conditions. To do research first identified and selected parameters effect on flow, including vegetation type, velocity, submerged ratio, density and absorption surface momentum and using dimensional analysis relations between roughness coefficient and dimensionless were obtained. Then 182 experiments were conducted on a laboratory flume and effect of parameters on the roughness coefficient was evaluated. By using of results, relations obtained from dimensional analysis were calibrated. Research results can be possible to calculate the friction factors with have above parameters. Roughness coefficients reduce with increasing of flow rate to be nonlinear and severely, for example increase velocity from 0.2 m/s to 2 m/s make Manning’s coefficient reduces to one third of the first case. But reducing amount of coefficient with decrease of submergence ratio and density compared with  the velocity is low and decreasing  trend  is linear trend, For example if density was reduced from greater category to  lower category, value of manning coefficient reduce maximum by ten percent.}, keywords = {Friction Factors,Vegetation,Flexibility,Non-Submerged}, title_fa = {تعیین ضریب زبری پوشش گیاهی در سواحل رودخانه‌ها و دشت‌های سیلابی در حالت غیر مستغرق}, abstract_fa = {به دلیل انعطاف پذیری پوشش گیاهی واقع در سواحل رودخانه‌ها و دشت‌های سیلابی، ضریب زبری در این مناطق متغیر بوده و تابعی از مشخصات جریان و خصوصیات پوشش گیاهی است. به دلیل وجود سازه‌های مهمی مانند ایستگاه‌های پمپاژ آب، جاده‌ها ، تصفیه خانه‌های آب و فاضلاب، استخرهای پرورش ماهی و میگو در کنار رودخانه‌ها و احداث سازه‌هایی مانند پل‌ها و بندهای انحرافی روی آن‌ها شناخت رفتار رودخانه به ویژه اثر پوشش گیاهی روی ضرایب زبری و به تبع ظرفیت عبور جریان از اهمیت بالایی برخوردار است. بدین منظور این تحقیق برای به دست آوردن روابط و مقادیر مناسب ضریب زبری پوشش گیاهی در سواحل رودخانه‌ها و دشت‌های سیلابی در حالت غیر مستغرق انجام شد. برای انجام تحقیق ابتدا با شناسایی و انتخاب پارامترهای مؤثر بر جریان شامل نوع پوشش گیاهی، سرعت جریان، نسبت استغراق، درصد تراکم و سطح جذب اندازه حرکت با استفاده از تجزیه و تحلیل ابعادی روابط بین ضرایب زبری و پارامترهای بدون بعد به دست آمد. سپس با انجام ۱۸۲ آزمایش روی یک فلوم آزمایشگاهی تأثیر هر یک از پارامترهای مؤثر بر جریان روی ضریب زبری مورد بررسی قرار گرفت و با استفاده از نتایج آن‌ها، روابط به دست آمده از تجزیه و تحلیل ابعادی واسنجی شد. از نتایج تحقیق می‌توان به امکان محاسبه­ی ضرایب زبری با داشتن پارامترهای فوق اشاره نمود. این ضرایب با افزایش سرعت جریان به صورت غیر خطی و شدید کاهش می‌یابند؛ به عنوان مثال در اثر تغییر سرعت از ۲/٠ به ٢ متر بر ثانیه ضریب زبری مانینگ به یک سوم حالت اول کاهش می‌یابد. اما کاهش مقدار ضریب زبری با کم شدن نسبت استغراق و درصد تراکم پوشش گیاهی در مقایسه با افزایش سرعت کم بوده و روند کاهش آن خطی است؛ به صورتی که در اثر تغییر از یک رده تراکم بیش‌تر به تراکم کم‌تر مقدار آن حداکثر ده درصد کاهش می‌یابد.}, keywords_fa = {Friction Factors,Vegetation,Flexibility,Non-Submerged}, url = {https://jise.scu.ac.ir/article_13476.html}, eprint = {https://jise.scu.ac.ir/article_13476_3d5725e766255bff1c4f5a6505ed159a.pdf} } @article { author = {Hassan Zadeh, Yousef}, title = {Determination of the drought periods by analyzing the hydrometeorological data}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {27-41}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13477}, abstract = {   This article presents an overview of the water resources available in Iran on one hand and Urmia lake catchments area, situated on the North-West of this country on the other. Water balances are presented for the Urmia lake catchments area and the water supply and consumption patterns in the Iranian main river basins. The drought periods occurrences have been analyzed using the forecasting methods and correlation laws between the discharges and the precipitation data measurements for the Adji-chai river, which is a river most representative of the Arid and Semi-arid region. The results obtained from using forecasting methods in data analysis indicated that drought phenomenon in Tabriz region and in general in Iran, is resulted from irregular time and spatial precipitation distributions in one hand, and severely negative fluctuations in precipitations and consequently highly reduced river flows on the other.}, keywords = {Drought periods,Hydrometeorology,Urmia lake,Water balance,Forecasting methods,Correlation laws,Adji-chai river}, title_fa = {بررسی دوره‌های خشکسالی با استفاده از تجزیه و تحلیل داده‌های هیدرومتئورولوژی}, abstract_fa = {در این مقاله، ضمن ارائه پتانسیل منابع آب کشور از یک سو و بیلان آبی حوضه آبریز دریاچه ارومیه واقع در شمال غرب کشور از سوی دیگر، با اعمال روش‌های احتمالاتی تجربی و ایجاد همبستگی بین داده‌های اندازه‌گیری شده از بارندگی‌ها و دبی جریان رودخانه آجی چای که یکی از رودخانه‌های حوضه آبریز دریاچه ارومیه بوده و می‌تواند معرف یکی از مهم‌ترین رودخانه‌های مناطق خشک و نیمه خشک نیز باشد، دوره‌های خشکسالی تعیین و مورد تجزیه و تحلیل قرار گرفته و روابط همبستگی و فرکانس تجربی داده‌ها به صورت دیاگرام‌های کاربردی ارائه شده است. نتایج مکتسبه از کاربرد روش‌های احتمالاتی تجربی در تجزیه و تحلیل داده‌ها بیانگر آن است که پدیده خشکسالی در منطقه تبریز و در حالت کلی در کشور، ناشی از توزیع ناموزون زمانی و مکانی بارندگی‌ها و دبی جریان از یکسو و نوسانات شدید منفی در بارندگی‌ها و کاهش شدید جریان رودخانه‌ها از سوی دیگر می‌باشد.}, keywords_fa = {Drought periods,Hydrometeorology,Urmia lake,Water balance,Forecasting methods,Correlation laws,Adji-chai river}, url = {https://jise.scu.ac.ir/article_13477.html}, eprint = {https://jise.scu.ac.ir/article_13477_25486b335f6ecbf26cb56f07d5ae236c.pdf} } @article { author = {Lashkarara, Babak and Fathi Moghadam, Manoochehr and Mohammad Vali Samani, Hossain}, title = {Wall and bed shear stress in smooth rectangular channels}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {43-52}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13478}, abstract = {   This Study reports on experiments concerning the boundary shear stress and boundary shear force distributions in a smooth rectangular channel. The boundary shear stresses were measured with a 4-mm outside diameter Preston tube in conjunction with a differential pressure transducer. The calibration curves of Patel (1965) were used to convert pressure reading to boundary shear stresses. Nonlinear regression-based equations are drive from experimental analysis to determine percentage of the total shear force carried by the walls and mean wall and bed shear stresses around wetted perimeter. The proposed equations compared to previous researches are shown to higher correlation coefficient and smaller standard deviation. Furthermore, single variable equations are introduced in the paper indeed an advantage compared to that of other studies.}, keywords = {Shear Stress,Shear force,Preston Tube}, title_fa = {تعیین تنش برشی متوسط کف و جداره ی در کانال های مستطیلی صاف}, abstract_fa = {مطالعات حاضر بر پایه ی نتایج آزمایشگاهی به منظور تعیین توزیع تنش برشی در کانال های مستطیلی صاف ارائه شده است. جهت تعیین تغییرات تنش برشی موضعی  از لوله ی پرستون با قطر خارجی 4 میلیمتر مجهز به سلول های حساس به فشار دینامیک استفاده شده است. جهت تبدیل فشار قرائت شده به تنش برشی از منحنی کالیبراسیون پتل استفاده گردید. آنالیز نتایج آزمایشگاهی با استفاده از معادلات رگرسیون غیر خطی منجر به معرفی معادلاتی جهت تعیین درصد نیروی برشی کل وارده بر جداره ی ها و متوسط تنش برشی جداره ی و کف کانال در اطراف محیط مرطوب گردیده است. مقایسه ی نتایج حاصل از تحقیق حاضر با مطالعات قبلی، حاکی از درجه ی همبستگی بالاتر و انحراف از معیار کوچک تر معادلات پیشنهادی می باشد. از طرفی معرفی معادلات تک پارامتری در تحقیق حاضر را می توان از مزایای آن نسبت به مطالعات قبلی برشمرد.}, keywords_fa = {Shear Stress,Shear force,Preston Tube}, url = {https://jise.scu.ac.ir/article_13478.html}, eprint = {https://jise.scu.ac.ir/article_13478_49b4b9446b9854e97de1fba645a18a60.pdf} } @article { author = {khozeymehnezhad, Hossein and shafai bajestan, mahmood}, title = {Sediment particles incipient motion criteria at closed box conduits}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {51-61}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13479}, abstract = {   Deposition of sediment inside the conduit structures; eg inverted siphon; reduces the flow cross section area and increase the flow roughness which causes reduction of flow discharge passing through the conduit. In order the structure to function properly, the structure should design not to allow any sediment particle to deposit. Or if deposited, it can be possible to remove them by the action of flow. Among the methods in which can be achieved such goals is to design the structure in such a way that the flow velocity to be greater than incipient motion velocity. There are many relations to obtain the incipient motion velocity of sediment particles on the bed or slope of an open channel. However for the case of closed conduits under low pressure little information is available. Such criterion is useful for sewer cleaning too. To determine the criteria for determining the incipient motion velocity at closed box conduits this study was conducted. To do so first a general relationship was developed by applying the dimensional analysis and then experimental tests were conducted to obtain data. In these tests five different sediment particle sizes, 0.5, 0.7, 1.0, 2.0 and 3.2 millimeters under four different bed slopes 0.0, 8.0, 16, and 24 degrees were conducted. By analyzing of these data design charts were developed. From these curves, the incipient motion velocity can be determined. The results were compared with the results of other investigators. The application of this study in some of the inverted siphons in Khuzestan province of Iran has been presented.}, keywords = {Incipient motion,Box cross section conduits,Sediments,Inverted Siphon,Sedimentation control}, title_fa = {معیار آستانه ی حرکت ذرات رسوبی در مجاری بسته با مقطع مربع شکل}, abstract_fa = {نهشته شدن رسوب در سازه‌های انتقال آب، از جمله سیفون معکوس، باعث کاهش سطح مقطع جریان و همچنین افزایش زبری می­شود که در نتیجه کاهش آبدهی سازه را به دنبال خواهد داشت. به منظور عملکرد صحیح سازه، ضروری است تا این سازه طوری طراحی گردد تا از تجمع رسوب در مسیر انتقال آب جلوگیری کند و یا در صورت نهشته شدن بتوان با ایجاد شرایط لازم رسوبات را تخلیه کرد. از جمله روش­های جلوگیری از نهشته شدن رسوب و یا خروج آن‌ها، منظور نمودن سرعت جریان بیش از سرعت آستانه­ی حرکت ذرات می­باشد. تاکنون مطالعات زیادی برای تعیین آستانه­ی حرکت ذرات رسوبی در بستر یا بدنه­ی کانال­ها انجام شده است ولی در خصوص جریان در مقاطع بسته از جمله سیفون معکوس مطالعه­ی اندکی صورت گرفته است. در تحقیق حاضر ابتدا با استفاده از آنالیز ابعادی رابطه­ی کلی برای شرایط آستانه­ی حرکت ذرات در مقاطع مربع ایجاد شد. سپس با احداث مدل آزمایشگاهی و به کار بردن پنج نمونه رسوب غیر چسبنده با اندازه 5/0، 7/0، 1، 2 و 2/3 میلی­متر تحت چهار شیب متغیر 0، 8، 16 و 24 درجه آزمایش­های لازم انجام گرفت. نتایج به صورت منحنی­هایی ارائه شده است. با به کار بردن این منحنی­ها می­توان سرعت آستانه­ی حرکت را در مقاطع تحت فشار مربعی به دست آورد. همچنین کاربرد نتایج این تحقیق در تعدادی از سیفون­های معکوس استان خوزستان ارائه شده است}, keywords_fa = {Incipient motion,Box cross section conduits,Sediments,Inverted Siphon,Sedimentation control}, url = {https://jise.scu.ac.ir/article_13479.html}, eprint = {https://jise.scu.ac.ir/article_13479_6e26858185594976d1ae9b0b2c608087.pdf} } @article { author = {Omid, Mohammad Hosain and Hamidifar, Hossein and Nasr Abadi, Mohsen}, title = {Effect of tailwater depth on local scour downstream of horizontal jets}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {63-74}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13480}, abstract = {   In this paper the results of an experimental study on the effect of tailwater depth on the mechanism of scouring downstream of hydraulic jumps is presented. Totally, 53 tests with 12 hours run time were carried out under various tailwater depths ranging from 14.2 to 32.5 cm for 5 different densimetric Froude numbers. The results show that the tailwater depth has a significant role in the scouring process and its effect depends on the magnitude of densimetric Froude numbers. For high values of the Froude number, there is a critical submergence value, where the minimum depth of the scour hole is occurred. An empirical equation is proposed to determine this critical submergence factor. Considering the mechanism of a submerged jet issuing from a sluice gate opening and passing a sudden step, a new approach is proposed to justify the presence of critical submergence factor. Comparing the present results with those of previous studies shows that the length of apron is also an important factor in the scouring process. Non-dimensional graphs are presented to determine the magnitude of scour depth for different tailwater depth and Froude numbers. Finally, it was found that the maximum scour depth and the dune height are more impressible to the variations of the tailwater depth than scour hole length.}, keywords = {Local scour,Tailwater depth,Hydraulic jump,Critical Submergence factor}, title_fa = {اثر عمق پایاب بر تشکیل حفره آبشستگی در پایین‌دست جت افقی}, abstract_fa = {در این مقاله، نتایج حاصل از مطالعه آزمایشگاهی تاثیر عمق پایاب بر آبشستگی موضعی پایین‌دست جهش هیدرولیکی ارایه شده است. در مجموع 53 آزمایش با زمان اجرای 12 ساعت، در دامنه اعماق پایاب مختلف 5/32-2/14 سانتی‌متر و به ازای 5 عدد فرود ذره متفاوت انجام شد. نتایج نشان می‌دهد که عمق پایاب یک پارامتر بسیار تأثیرگذار در میزان آبشستگی است و چگونگی تاثیر آن به عدد فرود ذره و میزان استغراق بستگی دارد، به گونه‌ای که یک فاکتور استغراق بحرانی وجود دارد که در آن حداقل عمق آبشستگی رخ می‌دهد.  بر این اساس و در دامنه آزمایش‌های این تحقیق، رابطه‌ای برای تعیین این مقدار بحرانی بر حسب عدد فرود ذره ارائه شده است. نتایج بدست آمده با تحقیقات پیشین مقایسه و مشخص شد که با کاهش طول کف بند، تاثیر عمق پایاب بیشتر می‌شود. همچنین نمودارهای بدون بعدی برای تعیین میزان آبشستگی در شرایط عمق پایاب و اعداد فرود ذره مختلف ارائه شد. در نهایت مشاهده شد که از میان پارامترهای مشخصه حفره آبشستگی، تأثیرپذیری حداکثر عمق آبشستگی و ارتفاع تل ماسه از عمق پایاب نسبت به گسترش طولی حفره بیشتر است.}, keywords_fa = {Local scour,Tailwater depth,Hydraulic jump,Critical Submergence factor}, url = {https://jise.scu.ac.ir/article_13480.html}, eprint = {https://jise.scu.ac.ir/article_13480_ada7c7f604cf1040da03cdf88b8296dc.pdf} } @article { author = {Razavi Toosi, Seyedeh Laila and Ayyoubzadeh, Seyed Ali and Vali Zadeh, Ali Reza}, title = {The influence of time scale in free surface flow simulation using Smoothed Particle Hydrodynamics (SPH)}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {75-92}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13481}, abstract = {   In hydrodynamic and hydraulic science, free surface flows are important but they are difficult to simulate because boundary conditions are required on an arbitrarily moving surface. Smoothed particle hydrodynamics (SPH) is a meshfree, Lagrangian particle method for modeling free surface flows such as dam break. One of problems in SPH is time consuming calculations in cases that they occurrence time are large. They need computers with strong CPU and memory. Recently, the parallel is used in this situation. In this paper, the influence of time scale in free surface flow simulation using SPH is considered. Dam break simulation with SPH in different scales is investigated and time scale influence is then obtained. For SPH model verification, the results were compared with experimental and numerical results of pervious researches. The dam break results as free surface flow show that the model with less scale model has less time of occurrence. Thus, the computer run time was decreased. The relation between two scales in dam break simulation indicates that the Froude law for free surface flow is valid. For models with scales of 3 and 6 with equal number of particles, the time of occurrence and computation were decreased about 42% and 59%, respectively. Therefore the computers run time can be decreased when this new-proposed scheme isused.}, keywords = {Dam break,Time scale,Smoothed Particle Hydrodynamic,Free surface flow simulation}, title_fa = {تأثیر مقیاس زمان در شبیه سازی جریانات با سطح آزاد با استفاده از روش هیدرودینامیک ذرات هموار (SPH)}, abstract_fa = {جریانات با سطح آزاد در علوم هیدرودینامیک و هیدرولیک دارای اهمیت زیادی می­باشند. شبیه­سازی این جریانات به علت شرط مرزی متحرک آن‌ها مشکل می­باشد. روش هیدرودینامیک ذرات هموار(SPH) یک روش ذره­ای، لاگرانژی و بدون شبکه­بندی است که در شبیه­سازی جریانات با سطح آزاد مانند شکست سد به کار برده می­شود. یکی از مشکلاتی که در شبیه­سازی SPH وجود دارد این است که زمان محاسبات برای شبیه­سازی پدیده­هایی که زمان وقوع آن‌ها طولانی است، بسیار زیاد می­باشد و نیاز به استفاده از رایانه‌ها با سرعت زیاد و یا موازی کردن رایانه­هاست. در این مقاله روشی برای کاهش تعداد محاسبات و در نتیجه کاهش زمان اجرای آن‌ها، با بررسی تأثیر مقیاس زمان در شبیه­سازی عددی جریانات دارای سطح آزاد در روش SPH ارائه شده است. نمونه مورد مطالعه، پدیده شکست سد می­باشد. برای صحت­سنجی مدل SPH، نتایج عددی شکست سد با نتایج آزمایشگاهی و نتایج حاصل از تحقیقات قبلی مقایسه شد. این نمونه در مقیاس­های مختلف بررسی و نتایج آن در زمان­های متناظر برای مقیاس­های طولی مختلف، محاسبه شده است. نتایج بدست آمده در شکست سد به عنوان یک جریان با سطح آزاد، نشان می­دهد که با کاهش مقیاس طولی، مقیاس زمان کاهش می­یابد و رابطه بین این دو مقیاس در شبیه­سازی عددی شکست سد، از قانون فرودی برای جریانات سطح آزاد پیروی می­کند. باریکه برای نسبت­های مقیاس 3 و 6، نسبت زمان وقوع پدیده در این مقیاس­ها به مقیاس اصلی، با تعداد ذرات یکسان به ترتیب به اندازه 3/42 و 2/59 درصد کاهش می­یابد. با بررسی­های انجام شده بر روی زمان اجرا توسط رایانه، در مدل­های مختلف مشخص شد که با کاهش مقیاس مدل، زمان اجرای آن توسط رایانه، به میزان قابل توجهی کاهش می­یابد. باریکه این کاهش برای مقیاس طولی 6 به میزان 2/58 درصد می­رسد. سپس مقایسه بین وقوع پدیده در زمان­های متناظر در مقیاس­های طولی مختلف با یکدیگر انجام شد. مقایسه نتایج نشان دادند که با کاهش مقیاس، با دقت یکسان، تعداد محاسبات و در نتیجه زمان آن‌ها کاهش می­یابد. این بدان معناست که با کاهش مقیاس مدل و انجام محاسبات مشابه، مقیاس زمان و در نتیجه زمان اجرای محاسبات کاهش می­یابد. از این رویکرد می­توان در جهت کاهش زمان انجام محاسبات برای پدیده­هایی که زمان وقوع آن‌ها طولانی است، در روش SPH استفاده کرد.}, keywords_fa = {Dam break,Time scale,Smoothed Particle Hydrodynamic,Free surface flow simulation}, url = {https://jise.scu.ac.ir/article_13481.html}, eprint = {https://jise.scu.ac.ir/article_13481_abc1042396be94064b469f493fe1c8e5.pdf} } @article { author = {Vaghefi, Mohammad and Ghodsian, Masoud}, title = {Experimental investigation on the effect of curvature of bend on bed topography in 90 degree bend}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {93-112}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13482}, abstract = {Rivers are main sources of water supply. Recognition of   rivers behavior and their changes, particularly in Curved channels, is critical. In this paper, results of experiments on scour pattern in a 90 degree bend are discussed.  Experiments have been carried out in a channel with three different radiuses of curvatures, including mild, moderate and steep. Bed topography has been measured by Laser Bed Profiler. Comparison between different lateral sections, longitudinal sections and bed topography has been made and scouring pattern is analyzed. The results indicate that reduction of radius of curvature of the bend leads to increase of bed topography changes and sedimentation and scouring rates. Also, scour can be seen along downstream straight channel and near the outer bank; however, this is more evident in the steeper bend.}, keywords = {Scour pattern,90 Degree bend,Bed topography,Radius of curvature}, title_fa = {بررسی آزمایشگاهی تأثیر شعاع انحنای قوس 90 درجه بر تغییرات توپوگرافی بستر}, abstract_fa = {رودخانه‌ها اصلی‌ترین منبع تأمین آب می‌باشند بنابراین شناخت رفتار رودخانه‌ها و تغییرات آن‌ها خصوصاً در کانال‌های قوسی بسیار حائز اهمیت می‌باشد. در این مقاله به اندازه گیری آزمایشگاهی الگوی آبشستگی در قوس 90 درجه و کانال مستقیم پایین دست آن تحت تأثیر تغییر پارامتر شعاع انحنای قوس پرداخته شده است. آزمایشات در یک کانال آزمایشگاهی با سه شعاع انحنای ملایم، متوسط و تند انجام گرفته است. تغییرات توپوگرافی بستر با استفاده از دستگاه برداشت پروفیل بستر لیزری اندازه گیری شده است. مقایسه بین مقاطع مختلف عرضی، طولی و توپوگرافی بستر انجام شده و الگوی آبشستگی مورد تجزیه و تحلیل قرار گرفته است. نتایج بیانگر این است که با کاهش شعاع انحنای قوس، تغییرات توپوگرافی بستر و میزان آبشستگی و رسوب‌گذاری بیشتر می‌شود. همچنین در مسیر مستقیم پایین دست، آبشستگی در نزدیکی ساحل خارجی مشاهده می‌شود که در قوس تند مشهود تر است.}, keywords_fa = {Scour pattern,90 Degree bend,Bed topography,Radius of curvature}, url = {https://jise.scu.ac.ir/article_13482.html}, eprint = {https://jise.scu.ac.ir/article_13482_8df123cfb57573fa5f8ce2d482911051.pdf} } @article { author = {Anvari, Sedigheh and Morid, Saeid and Saghafian, Bahram}, title = {Comparison of Fuzzy and ANN models performance for monthly flow forecast using short time data}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {113-126}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13483}, abstract = {   Regarding the bottom outlet gates, the optimal hydraulic design to ensure non-occurrence of destructive vibrations is very important. Forces inserted into the gates due to the flow with high hydrostatic pressure under the gates may cause creation of damage on the lower edge of gates. Compressive hydrostatic force along with the gate weight and friction forces determine the required powers for down-pull (or uplift) of the gates which is also affected by the geometric shape and flow passing under the gates. The existence of high pressure flow in the upstream of bottom outlet gates, as well as the small quantities of gate opening compared to the head water, may cause using common theoretical methods result in significant errors in the determination of different involved parameters. Therefore there is a need for accurate laboratory studies. In this paper, the results of the study on the physical model of bottom channel and service and emergency gates of Narmasheer Dam is presented. Also the results of measurements of exerted forces gate and vibrations into the gates are provided. The necessary tests have been made, so that using the measured pressure distribution on the gates, vertical forces and maximum damage in both normal head tank and various gate openings, were determined respectively. The exerted forces were calculated based on the use of pressure distribution obtained by piezometers installed above and under the gates. In this study, the maximum horizontal force appears on the 2 percent gate opening and is equivalent to 2410 (KN). The maximum horizontal force into the emergency gate has also occurred in the initial gate opening situation with a value of 2507 (KN). The experimental results also indicated that the maximum operation frequency of vibration due to the high pressure flow in the bottom outlet channel is 80 per second. The tests showed that by increasing the diameter of gate lift arm, the frequency of vibration can be controlled.}, keywords = {Vibration,Emergency gate,Service gate,Bottom outlet,Physical model,Down pull force,Narmasheer dam}, title_fa = {مقایسه عملکرد مدل‌های شبکه عصبی و فازی در تعیین دبی ماهانه جریان با استفاده از آمار کوتاه مدت.}, abstract_fa = {بهره‌برداری بهینه از سیستم­های منابع آب و به خصوص تعیین زمان واقعی کارکرد مخازن سدها، مستلزم پیش‌بینی آورد رودخانه‌هاست. در این مقاله عملکرد مدل‌های منطق فازی (FL) و شبکه عصبی مصنوعی (ANN) برای پیش‌بینی یک و دو ماه بعد جریان حوضه کارون در محل ایستگاه هیدرومتری پل­شالو با هم مقایسه شده است. در این راستا از سیستم استنتاجی ممدانی برای ساخت مدل‌های FL و همچنین شبکه­های پیشرو سه لایه برای مدل‌سازی توسط ANN استفاده گردید. بررسی عملکرد این مدل‌ها با شاخص‌های ضریب تبیین(R2)، میانگین قدر مطلق خطا (MAE) و ریشه میانگین مربعات خطا (RMSE) نشان داد که در شرایط کم بودن داده‌ها، مدل FL نسبت به مدل ANN در پیش‌بینی یک و دو ماه بعد جریان از نظر آماری عملکرد بهتری داشته است. این عملکرد بهتر به طور متوسط مقادیری برابر 25% و 7% را به ترتیب برای R2 و RMSE در پیش­بینی جریان اسفند ماه به همراه داشته است. نتایج بدست آمده از این دو مدل با مدل رگرسیون خطی چندگانه (MLR) نیز مقایسه گردید که عدم عملکرد مناسب آن را نشان می‌داد.}, keywords_fa = {Vibration,Emergency gate,Service gate,Bottom outlet,Physical model,Down pull force,Narmasheer dam}, url = {https://jise.scu.ac.ir/article_13483.html}, eprint = {https://jise.scu.ac.ir/article_13483_22d0c7aa7e4faccecfc989392344405d.pdf} } @article { author = {Heydari orojlo, Siavash and Mousavi Jahromi, Seyed Habib and Adib, Arash}, title = {Influence of the steeped spillway slope on the number of optimal steps}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {127-140}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13484}, abstract = {In the present study 54 step spillways make of ple Glass, 5 discharges (10, 20, 30, 40 and 50 l/s/m) and 3 slopes, z=1.7 , z=2 and z=2.5 (totally 275 experiments were conducted). Finding of the present study are as follows: 1- Performed modeling observations revealed that the relative energy dissipation along with spillway will be decreased with increasing discharge. 2- It is shown that energy dissipation is increase with increasing step numbers, but energy dissipation will be stopped in a certain number of steps. 3- According to presented study, optimal number of steps base on different values of yc/h and Froude Number is determined for the maximum energy dissipation. It is shown that optimal number of steps is affected by slope of spillway. Increasing spillway slope causes more energy dissipation.}, keywords = {Stepped spillway,Maximum energy dissipation,Number of optimal step,Physical modeling}, title_fa = {بررسی تأثیر شیب بر تعداد بهینه پلکان‌ها در سرریزهای پلکانی}, abstract_fa = {   در این تحقیق تعداد 54 مدل فیزیکی از سرریز های پلکانی با سه شیب مختلف º8/21(z=2.5)، º56/26(z=2) و º30 (z=1.7) ساخته و مورد آزمایش قرار گرفت. نوع تاج سرریزها از منحنی استاندارد اوجی است و پلکان‌ها با شیب‌های ثابت z=1.7، z=2 و z=2.5 تا پاشنه پایین دست سرریز ادامه دارد. جهت مطالعه اثر تعداد پله‌ها در افت انرژی، تعداد پله‌های 39، ...،2،3،5،7 عدد منظور شد. هدف، بررسی تأثیر تعداد پلکان در میزان افت انرژی جریان و در نهایت بدست آوردن تعداد بهینه پلکان در این نوع از سرریزها به گونه‌ای که بیشترین میزان افت انرژی حاصل گردد می‌باشد. آزمایشات با 5 دبی مختلف (10-20- ... -50 لیتر بر ثانیه) در آزمایشگاه هیدرولیک دانشکده مهندسی علوم آب دانشگاه شهید چمران اهواز انجام گردید که مجموعاً 270 آزمایش انجام گرفت. نتایج حاصل از این پژوهش نشان می‌دهند که به ازاء انرژی ثابت بالادست، افزایش تعداد پله‌ها به میزان قابل توجهی باعث افزایش استهلاک انرژی می‌گردد، اما اگر چنانچه این تعداد از حد معینی تجاوز کند، اثر مثبت آن از بین می‌رود. همچنین بررسی‌ها نشانگر این مطلب می‌باشند که به ازاء افزایش دبی جریان در هر یک از شیب‌ها، حداکثر افت انرژی نسبی صورت گرفته در تعداد پلکان بالاتری رخ داده است. همچنین با افزایش شیب سرریز از 8/21 درجه به 30 درجه، حداکثر افت انرژی صورت گرفته در تعداد پلکان کمتری رخ می‌دهد.}, keywords_fa = {Stepped spillway,Maximum energy dissipation,Number of optimal step,Physical modeling}, url = {https://jise.scu.ac.ir/article_13484.html}, eprint = {https://jise.scu.ac.ir/article_13484_dd1bb5f71369ad4e999b454fa04ef44b.pdf} } @article { author = {Pour Eskandar, Sanaz and Salmasi, Farzin and Hossai Zadeh Dalir, Ali and Farsadi Zadeh, Davood}, title = {Experimental investigation of flow characteristics on discharge coefficient over compound rectangular broad-crested weir}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {141-156}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13485}, abstract = {Compound weirs are composed of two sections: 1.Lower entrance section 2.Upper entrance section. Lower entrance section is designed in different shapes such as rectangle, trapezoid, … and it works singly in low discharges. Flow discharge is measured accurately and sensitively according to weir shape in such a condition. In high discharges, upper entrance section prevents water surface from having remarkable increase at upstream of weir and provides the possibility of discharge measurement with acceptable accuracy. In this study, flow over 15 rectangular broad-crested weirs was simulated with different sizes in central width of weir, height and length of weir using experimental models and the effects of these parameters on discharge coefficient, velocity coefficient, and modular limit were investigated. Results show that with increasing dimensionless parameter: head to weir length (h1/L), discharge coefficient (Cd) increase, in other words, Cd in single section (h1/L)<0.24 is lower than compound weir section. Also this condition for h1/p<0.94 (p is weir height) is true. In compound weir condition, reduction in central cross section width and weir height causes to increase modular limit.}, keywords = {Compound broad-crested weir,Discharge Coefficient,Approach velocity coefficient,Modular limit}, title_fa = {بررسی آزمایشگاهی خصوصیات جریان بر روی ضریب دبی سرریز مرکب لبه پهن مستطیلی}, abstract_fa = {سرریز مرکب از دو قسمت، مرکز در پایین و دهانه در قسمت بالای خود تشکیل شده است. قسمت مرکزی دهانه به شکل­های مختلفی نظیر مستطیلی، ذوزنقه و طراحی می­شود و در جریان­های کم، به صورت منفرد عمل می­کند و اندازه­گیری جریان با توجه به شکل سرریز با دقت و حساسیت مناسبی انجام می­گیرد. در جریان­های زیاد، دهانه بالایی سرریز مانع افزایش زیاد سطح آب در بالادست سرریز شده و اندازه­گیری دبی را با دقت قابل قبولی امکان پذیر می­سازد. در این پژوهش سرریز لبه پهن مرکب با مقطع مستطیلی- مستطیلی با اندازه­های مختلف در قسمت عرض مرکزی سرریز، ارتفاع و طول­ سرریز با استفاده از 15 مدل آزمایشگاهی مورد بررسی قرار گرفته و تأثیر تغییر این پارامترها بر روی فاکتورهای ضریب دبی، ضریب سرعت و آستانه استغراق مورد بررسی قرار گرفته است. نتایج نشان می‌دهند که با افزایش نسبت بار آبی به طول سرریز (h1/L) ، مقدار ضریب دبی (Cd) افزایش یافته و به عبارت دیگر Cd در حالتی که مقطع ساده عمل می­کند (h1/L<0.24) کمتر از حالتی است که مقطع مرکب عمل می­کند. همین حالت برای زمانی که نسبت بار آبی به ارتفاع سرریز (h1/p) ­کمتر از 94/0 است، برقرار است. وقتی مقطع سرریز مرکب عمل می­کند، کاهش عرض در قسمت مرکزی و نیز کاهش ارتفاع باعث افزایش آستانه استغراق می‌شود.}, keywords_fa = {Compound broad-crested weir,Discharge Coefficient,Approach velocity coefficient,Modular limit}, url = {https://jise.scu.ac.ir/article_13485.html}, eprint = {https://jise.scu.ac.ir/article_13485_9da40fe2a3e98da28f9ada4a9ea79fd2.pdf} } @article { author = {tangsir, sareh and Kashluli, Heaidar ALi and Moazed, Hadi}, title = {Estimating near-saturated soil moisture curve using disc-permeameter data and comparing it with laboratorial method}, journal = {Irrigation Sciences and Engineering}, volume = {33}, number = {2}, pages = {157-166}, year = {2010}, publisher = {Shahid Chamran University of Ahvaz}, issn = {2588-5952}, eissn = {2588-5960}, doi = {10.22055/jise.2010.13486}, abstract = {Nitrogen (N) loss from irrigated cropland, especially in rice paddies, results in low N-use efficiency and groundwater contamination. Soil conditions that increase ammonium and nitrate ion retention alleviate these problems. Clinoptilolite, a naturally occurring zeolite with high ion-exchange capacity, may be used to adsorb ammonium and retard excess leaching of nitrate. The objectives of this research were to determine the effects of different rates of Na-zeolite application (0, 2, 4, 8 and 16 g/kg soil) on pore water velocity and leaching of ammonium and nitrate applied as ammonium nitrate fertilizer to a silt loam soil at a rate of 350 kg N/ha under saturated conditions similar to that of a rice paddy. The results indicated that Na-zeolite applications of 2, 4 and 8 g/kg soil increase the pore water velocity by 5.0%, 19. 9, 68.0 and 58/6% compared with the control treatment, respectively. The maximum relative concentration (c/co) all treatments for the nitrate breakthrough curve (BTC) occurred at pore volume of about 0.5. When applying 39.1 cm of leaching water, leached nitrate by 86.9%, 66.00% and 48.5% of total applied nitrate at the soil surface with zeolite applications of 2, 4 and 8 g/kg soil, respectively. Although the ammonium discharged from all treatments was negligible (3.95, 3.48, 3.13 and 2.28 percent of total applied ammonium at the soil surface), the statistical analysis indicated significant differences among treatments that received zeolites. The relationship between the hydrodynamic dispersion coefficient (D) of nitrate and pore water velocity (v) was not linear and by increasing zeolite application to the soil, the value of D increased as well.}, keywords = {Zeolite,nitrate,Ammonium,Breakthrough curve,Hydrodynamic Dispersion}, title_fa = {تخمین منحنی رطوبتی خاک نزدیک اشباع با استفاده از اطلاعات نفوذ سنج دیسک و مقایسه آن با روش آزمایشگاهی}, abstract_fa = {خصوصیات هیدرولیکی خاک مانند توزیع اندازه منافذ و مشخصات رطوبتی خاک در تفسیر مشخصات فیزیکی خاک و مدیریت روش­های کشاورزی بسیار مهم می­باشند. روش­های استاندارد رایج از قبیل صفحات فشاری و سندی باکس اغلب زمان بر و پر هزینه هستند. در این مطالعه یک روش ساده با دقت کافی برای تخمین منحنی رطوبتی، با استفاده از اطلاعات نفوذ پایدار پیشنهاد شده است. ابتدا سرعت­های نفوذ پایدار در مکش­های متوالی به ترتیب 15-،10-،6- ،3- و صفر سانتی­متر توسط نفوذ سنج دیسک در مزرعه اندازه­گیری شدند. سپس جهت تخمین هدایت هیدرولیکی در مکش­های ذکر شده از اطلاعات نفوذ سنج دیسک، از تحلیل پایدار الریک و رینولدز استفاده گردید. هدایت هیدرولیکی اشباع بهینه سازی شده حاصل از اندازه گیری­های صحرایی، به عنوان پارامتر اولیه برای برازش مدل بروکز کوری جهت تخمین پارامترهای b و BCα در نظر گرفته شد. پارامترها با رگرسیون بالایی (9/0<) از طریق برازش  شکل خطی معادله بروکز کوری توسط نرم افزار آماری SPSS.11، به جفت داده­های هدایت هیدرولیکی و مکش، تخمین زده شدند. منحنی­های رطوبتی تخمین زده شده به دو روش آزمایشگاهی (سندی باکس) و پیشنهادی، با یکدیگر مقایسه گشتند. مقادیر تخمین زده شده به روش پیشنهادی، کمتر از مقادیر تخمین زده شده به روش آزمایشگاهی بدست آمدند.}, keywords_fa = {Zeolite,nitrate,Ammonium,Breakthrough curve,Hydrodynamic Dispersion}, url = {https://jise.scu.ac.ir/article_13486.html}, eprint = {https://jise.scu.ac.ir/article_13486_725559e16aced589b9b470279a17b33b.pdf} }